upload px4 source & 13week report & meeting report(May)

+############################################################################
+#
+#   Copyright (c) 2020 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+add_subdirectory(init.d)

+############################################################################
+#
+#   Copyright (c) 2020 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+px4_add_romfs_files(
+	rcS
+)

+#!/bin/sh
+# Un comment and use set +e to ignore and set -e to enable 'exit on error control'
+set +e
+# Un comment the line below to help debug scripts by printing a trace of the script commands
+#set -x
+# PX4FMU startup script.
+#
+# NOTE: environment variable references:
+#    If the dollar sign ('$') is followed by a left bracket ('{') then the
+#    variable name is terminated with the right bracket character ('}').
+#    Otherwise, the variable name goes to the end of the argument.
+#
+#
+# NOTE: COMMENT LINES ARE REMOVED BEFORE STORED IN ROMFS.
+#
+#------------------------------------------------------------------------------
+set R /
+#
+# Mount the procfs.
+#
+mount -t procfs /proc
+
+#
+# Start CDC/ACM serial driver.
+#
+sercon
+
+#
+# Print full system version.
+#
+ver all
+
+if mft query -q -k MTD -s MTD_PARAMETERS -v /fs/mtd_params
+then
+	set PARAM_FILE /fs/mtd_params
+fi
+
+if mft query -q -k MTD -s MTD_PARAMETERS -v /dev/eeeprom0
+then
+	set PARAM_FILE /dev/eeeprom0
+fi
+
+#
+# Load parameters.
+#
+param select $PARAM_FILE
+if ! param load
+then
+	param reset_all
+fi
+
+#
+# Optional board architecture defaults: rc.board_arch_defaults
+#
+set BOARD_ARCH_RC_DEFAULTS ${R}etc/init.d/rc.board_arch_defaults
+if [ -f $BOARD_ARCH_RC_DEFAULTS ]
+then
+	echo "Board architecture defaults: ${BOARD_ARCH_RC_DEFAULTS}"
+	. $BOARD_ARCH_RC_DEFAULTS
+fi
+unset BOARD_ARCH_RC_DEFAULTS
+
+#
+# Optional board defaults: rc.board_defaults
+#
+set BOARD_RC_DEFAULTS ${R}etc/init.d/rc.board_defaults
+if [ -f $BOARD_RC_DEFAULTS ]
+then
+	echo "Board defaults: ${BOARD_RC_DEFAULTS}"
+	. $BOARD_RC_DEFAULTS
+fi
+unset BOARD_RC_DEFAULTS
+
+#
+# Start system state indicator.
+#
+rgbled start -X -q
+rgbled_ncp5623c start -X -q
+rgbled_pwm start
+
+if param greater -s LIGHT_EN_BLINKM 0
+then
+	if blinkm start -X
+	then
+		blinkm systemstate
+	fi
+fi
+
+#
+# board sensors: rc.sensors
+#
+set BOARD_RC_SENSORS ${R}etc/init.d/rc.board_sensors
+if [ -f $BOARD_RC_SENSORS ]
+then
+	echo "Board sensors: ${BOARD_RC_SENSORS}"
+	. $BOARD_RC_SENSORS
+fi
+unset BOARD_RC_SENSORS
+
+#
+# Start UART/Serial device drivers.
+# Note: rc.serial is auto-generated from Tools/serial/generate_config.py
+#
+. ${R}etc/init.d/rc.serial
+
+# Check for flow sensor
+if param compare SENS_EN_PX4FLOW 1
+then
+	px4flow start -X
+fi
+
+uavcannode start
+unset R

+############################################################################
+#
+#   Copyright (c) 2018 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+add_subdirectory(init.d)
+add_subdirectory(mixers)
+# TODO: make this configurable from the board config, or better combine
+if("${PX4_BOARD}" MATCHES "sitl")
+	add_subdirectory(mixers-sitl)
+	add_subdirectory(init.d-posix)
+endif()

+############################################################################
+#
+#   Copyright (c) 2020 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+add_subdirectory(airframes)
+
+px4_add_romfs_files(
+	rc.replay
+	rcS
+)

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL
+#
+# @type Quadrotor Wide
+#
+# @maintainer Julian Oes <julian@oes.ch>
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER quad_w

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL
+#
+# @type Quadrotor Wide
+#
+# @maintainer Julian Oes <julian@oes.ch>
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+. ${R}etc/init.d/rc.ctrlalloc
+
+if [ $AUTOCNF = yes ]
+then
+	param set MPC_USE_HTE 0
+
+	param set VM_MASS 1.5
+	param set VM_INERTIA_XX 0.03
+	param set VM_INERTIA_YY 0.03
+	param set VM_INERTIA_ZZ 0.05
+
+	param set CA_AIRFRAME 0
+	param set CA_METHOD 1
+	param set CA_ACT0_MIN 0.0
+	param set CA_ACT1_MIN 0.0
+	param set CA_ACT2_MIN 0.0
+	param set CA_ACT3_MIN 0.0
+	param set CA_ACT0_MAX 1.0
+	param set CA_ACT1_MAX 1.0
+	param set CA_ACT2_MAX 1.0
+	param set CA_ACT3_MAX 1.0
+
+	param set CA_MC_R0_PX 0.1515
+	param set CA_MC_R0_PY 0.245
+	param set CA_MC_R0_CT 6.5
+	param set CA_MC_R0_KM 0.05
+	param set CA_MC_R1_PX -0.1515
+	param set CA_MC_R1_PY -0.1875
+	param set CA_MC_R1_CT 6.5
+	param set CA_MC_R1_KM 0.05
+	param set CA_MC_R2_PX 0.1515
+	param set CA_MC_R2_PY -0.245
+	param set CA_MC_R2_CT 6.5
+	param set CA_MC_R2_KM -0.05
+	param set CA_MC_R3_PX -0.1515
+	param set CA_MC_R3_PY 0.1875
+	param set CA_MC_R3_CT 6.5
+	param set CA_MC_R3_KM -0.05
+
+fi
+
+set MIXER direct

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (foggy_lidar)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_RNG_AID 1
+	param set EKF2_RNG_A_HMAX 10
+fi

+#!/bin/sh
+#
+# @name IF750A SITL
+# InspiredFlight 750 Auterion edition. Gazebo Only.
+#
+# @type Quadrotor
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	# EKF2: Multi GPS blending (as the model has 2 GPS's)
+	param set EKF2_GPS_MASK 7 # Uses speed, hpos and vpos accuracy
+	param set TRIG_INTERFACE 3
+	param set TRIG_MODE 4
+	param set MNT_MODE_IN 4
+	param set MNT_MODE_OUT 2
+	param set MNT_DO_STAB 2
+fi
+
+set MIXER quad_x

+#!/bin/sh
+#
+# @name PX4Vision SITL
+# Holybro px4vision. Gazebo Only.
+#
+# @type Quadrotor
+#
+
+. ${R}etc/init.d/airframes/4016_holybro_px4vision
+
+set MIXER quad_x

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (Optical Flow)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	# EKF2
+	param set EKF2_AID_MASK 2
+	param set EKF2_EVP_NOISE 0.05
+	param set EKF2_EVA_NOISE 0.05
+
+	# LPE: Flow-only mode
+	param set LPE_FUSION 242
+	param set LPE_FAKE_ORIGIN 1
+
+	param set MPC_ALT_MODE 2
+fi

+
+# shellcheck disable=SC2154
+mavlink stream -r 50 -s DISTANCE_SENSOR -u $udp_gcs_port_local

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (irlock)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	# enable fusion of landing target velocity
+	param set LTEST_MODE 1
+	param set PLD_HACC_RAD 0.1
+fi
+
+# Start up Landing Target Estimator module
+landing_target_estimator start

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (rplidar)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	param set LPE_FUSION 242
+fi

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (Vision)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	# EKF2: Vision position and heading
+	param set EKF2_AID_MASK 24
+	param set EKF2_EV_DELAY 5
+
+	# LPE: Vision + baro
+	param set LPE_FUSION 132
+
+	# AEQ: External heading set to use vision input
+	param set ATT_EXT_HDG_M 1
+fi

+
+# shellcheck disable=SC2154
+mavlink stream -r 30 -s ODOMETRY -u $udp_gcs_port_local

+#!/bin/sh
+#
+# @name Solo
+#
+# @type Quadrotor
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set MC_PITCHRATE_P 0.1
+	param set MC_ROLLRATE_P 0.1
+fi
+
+set MIXER quad_x

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (Obstacle Avoidance)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	param set COM_OBS_AVOID 1
+	param set MPC_XY_CRUISE 5.0
+fi

+# shellcheck disable=SC2154
+mavlink start -x -u 14558 -r 4000000 -m onboard -o 14541 -p # add mavlink stream for SDK

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (RTPS)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris

+#!/bin/sh
+# shellcheck disable=SC2154
+
+micrortps_client start -t UDP -r $((2019+2*px4_instance)) -s $((2020+2*px4_instance))

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (Optical Flow)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	# EKF2
+	param set EKF2_AID_MASK 2
+	param set SENS_FLOW_ROT 0
+
+	# LPE: Flow-only mode
+	param set LPE_FUSION 242
+	param set LPE_FAKE_ORIGIN 1
+
+	param set MPC_ALT_MODE 2
+fi

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (Vision Velocity)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	# EKF2: Vision velocity and heading
+	param set EKF2_AID_MASK 272
+	param set EKF2_EV_DELAY 5
+fi

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor SITL (Dual GPS)
+#
+# @type Quadrotor Wide
+#
+
+. ${R}etc/init.d-posix/airframes/10016_iris
+
+if [ $AUTOCNF = yes ]
+then
+	# EKF2: Multi GPS blending
+	param set EKF2_GPS_MASK 7 # Uses speed, hpos and vpos accuracy
+fi

+#!/bin/sh
+#
+# @name UUV
+#
+
+. ${R}etc/init.d/rc.uuv_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	#Set data link loss failsafe mode (0: disabled)
+	param set NAV_DLL_ACT 0
+
+	# disable circuit breaker for airspeed sensor
+	param set CBRK_AIRSPD_CHK 162128
+
+	#param set CBRK_GPSFAIL 240024
+fi
+
+set MAV_TYPE 12
+param set MAV_TYPE ${MAV_TYPE}
+
+set MIXER_FILE etc/mixers-sitl/uuv_x_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Hippocampus UUV
+#
+
+. ${R}etc/init.d/rc.uuv_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	#Set data link loss failsafe mode (0: disabled)
+	param set NAV_DLL_ACT 0
+
+	# disable circuit breaker for airspeed sensor
+	param set CBRK_AIRSPD_CHK 162128
+
+	#param set CBRK_GPSFAIL 240024
+fi
+
+set MAV_TYPE 12
+param set MAV_TYPE ${MAV_TYPE}
+
+set MIXER_FILE etc/mixers-sitl/uuv_x_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name BlueROV2 Heavy Configuration
+#
+
+. ${R}etc/init.d/rc.uuv_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	#Set data link loss failsafe mode (0: disabled)
+	param set NAV_DLL_ACT 0
+
+	# disable circuit breaker for airspeed sensor
+	param set CBRK_AIRSPD_CHK 162128
+
+fi
+
+set PWM_OUT 12345678
+set MIXER_FILE etc/mixers-sitl/vectored6dof_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Plane SITL
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_ARSP_THR 8
+	param set EKF2_FUSE_BETA 1
+	param set EKF2_MAG_ACCLIM 0
+	param set EKF2_MAG_YAWLIM 0
+
+	param set FW_LND_AIRSPD_SC 1
+	param set FW_LND_ANG 8
+	param set FW_THR_LND_MAX 0
+
+	param set FW_L1_PERIOD 12
+
+	param set FW_MAN_P_MAX 30
+
+	param set FW_PR_I 0.4
+	param set FW_PR_P 0.9
+	param set FW_PR_FF 0.2
+	param set FW_PSP_OFF 2
+	param set FW_P_LIM_MAX 32
+	param set FW_P_LIM_MIN -15
+
+	param set FW_RR_FF 0.1
+	param set FW_RR_P 0.3
+
+	param set FW_THR_MAX 0.6
+	param set FW_THR_MIN 0.05
+	param set FW_THR_CRUISE 0.25
+
+	param set FW_T_ALT_TC 2
+	param set FW_T_CLMB_MAX 8
+	param set FW_T_HRATE_FF 0.5
+	param set FW_T_SINK_MAX 2.7
+	param set FW_T_SINK_MIN 2.2
+	param set FW_T_TAS_TC 2
+
+	param set FW_W_EN 1
+
+	param set MIS_LTRMIN_ALT 30
+	param set MIS_TAKEOFF_ALT 30
+
+	param set NAV_ACC_RAD 15
+	param set NAV_DLL_ACT 2
+	param set NAV_LOITER_RAD 50
+
+	param set RWTO_TKOFF 1
+
+fi
+
+set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Plane SITL with camera
+#
+
+. ${R}etc/init.d-posix/airframes/1030_plane
+
+if [ $AUTOCNF = yes ]
+then
+	# Camera trigger interface is MAVLink
+	param set TRIG_INTERFACE 3
+	# Distance trigger mode enabled
+	param set TRIG_MODE 4
+fi

+#!/bin/sh
+#
+# @name Plane SITL with catapult
+#
+
+. ${R}etc/init.d-posix/airframes/1030_plane
+
+if [ $AUTOCNF = yes ]
+then
+	param set RWTO_TKOFF 0
+
+fi

+#!/bin/sh
+#
+# @name Plane SITL with downward facing LIDAR.
+#
+
+. ${R}etc/init.d-posix/airframes/1030_plane
+
+if [ $AUTOCNF = yes ]
+then
+	param set FW_LND_USETER 1
+
+fi

+#!/bin/sh
+#
+# @name Plane SITL
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_ARSP_THR 8
+	param set EKF2_FUSE_BETA 1
+	#param set EKF2_MAG_ACCLIM 0
+	#param set EKF2_MAG_YAWLIM 0
+
+	param set FW_LND_AIRSPD_SC 1.1
+	param set FW_LND_ANG 5
+	param set FW_THR_LND_MAX 0
+	param set FW_LND_HHDIST 30
+	param set FW_LND_FL_PMIN 9.5
+	param set FW_LND_FL_PMAX 20
+	param set FW_LND_FLALT 5
+	param set FW_LND_TLALT 15
+
+	param set FW_L1_PERIOD 25
+
+	param set FW_P_TC 0.4
+	param set FW_PR_FF 0.40
+	param set FW_PR_I 0.05
+	param set FW_PR_P 0.05
+
+	param set FW_R_TC 0.45
+	param set FW_RR_FF 0.40
+	param set FW_RR_I 0.132
+	param set FW_RR_P 0.085
+
+	param set FW_W_EN 1
+
+	param set MIS_LTRMIN_ALT 30
+	param set MIS_TAKEOFF_ALT 20
+	param set MIS_DIST_1WP 2500
+	param set MIS_DIST_WPS 10000
+
+	param set NAV_ACC_RAD 15
+	param set NAV_DLL_ACT 2
+	param set NAV_LOITER_RAD 50
+
+	param set RWTO_TKOFF 1
+	#param set FW_THR_SLEW_MAX 0.3 # fix takeoff failure for JSBsim in autonomous mission mode.
+	param set RWTO_MAX_PITCH 20
+	param set RWTO_MAX_ROLL 10
+	#param set RWTO_MAX_THR 0.6		# fix takeoff failure for JSBsim in autonomous mission mode.
+	param set RWTO_PSP 8
+	param set RWTO_AIRSPD_SCL 1.8
+
+fi
+
+set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Plane SITL
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_ARSP_THR 8
+	param set EKF2_FUSE_BETA 1
+	#param set EKF2_MAG_ACCLIM 0
+	#param set EKF2_MAG_YAWLIM 0
+
+	param set FW_LND_AIRSPD_SC 1.1
+	param set FW_LND_ANG 5
+	param set FW_THR_LND_MAX 0
+	param set FW_LND_HHDIST 30
+	param set FW_LND_FL_PMIN 9.5
+	param set FW_LND_FL_PMAX 20
+	param set FW_LND_FLALT 5
+	param set FW_LND_TLALT 15
+
+	param set FW_L1_PERIOD 25
+
+	param set FW_P_TC 0.4
+	param set FW_PR_FF 0.40
+	param set FW_PR_I 0.05
+	param set FW_PR_P 0.05
+
+	param set FW_R_TC 0.45
+	param set FW_RR_FF 0.40
+	param set FW_RR_I 0.132
+	param set FW_RR_P 0.085
+
+	param set FW_W_EN 1
+
+	param set MIS_LTRMIN_ALT 30
+	param set MIS_TAKEOFF_ALT 20
+	param set MIS_DIST_1WP 2500
+	param set MIS_DIST_WPS 10000
+
+	param set NAV_ACC_RAD 15
+	param set NAV_DLL_ACT 2
+	param set NAV_LOITER_RAD 50
+
+	param set RWTO_TKOFF 1
+	#param set FW_THR_SLEW_MAX 0.3 # fix takeoff failure for JSBsim in autonomous mission mode.
+	param set RWTO_MAX_PITCH 20
+	param set RWTO_MAX_ROLL 10
+	#param set RWTO_MAX_THR 0.6		# fix takeoff failure for JSBsim in autonomous mission mode.
+	param set RWTO_PSP 8
+	param set RWTO_AIRSPD_SCL 1.8
+
+fi
+
+set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Plane SITL
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_ARSP_THR 8
+	param set EKF2_FUSE_BETA 1
+	param set EKF2_MAG_ACCLIM 0
+	param set EKF2_MAG_YAWLIM 0
+
+	param set FW_LND_AIRSPD_SC 1
+	param set FW_LND_ANG 8
+	param set FW_THR_LND_MAX 0
+
+	param set FW_L1_PERIOD 15
+
+	param set FW_P_TC 0.5
+	param set FW_PR_FF 0.40
+	param set FW_PR_I 0.05
+	param set FW_PR_P 0.05
+
+	param set FW_R_TC 0.7
+	param set FW_RR_FF 0.20
+	param set FW_RR_I 0.02
+	param set FW_RR_P 0.22
+
+	param set FW_L1_PERIOD 12
+
+	param set FW_W_EN 1
+
+	param set MIS_LTRMIN_ALT 30
+	param set MIS_TAKEOFF_ALT 30
+
+	param set NAV_ACC_RAD 15
+	param set NAV_DLL_ACT 2
+	param set NAV_LOITER_RAD 50
+
+	param set RWTO_TKOFF 1
+
+fi
+
+set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Plane SITL
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_ARSP_THR 8
+	param set EKF2_FUSE_BETA 1
+	#param set EKF2_MAG_ACCLIM 0
+	#param set EKF2_MAG_YAWLIM 0
+
+	param set FW_LND_AIRSPD_SC 1.1
+	param set FW_LND_ANG 5
+	param set FW_THR_LND_MAX 0
+	param set FW_LND_HHDIST 30
+	param set FW_LND_FL_PMIN 9.5
+	param set FW_LND_FL_PMAX 20
+	param set FW_LND_FLALT 5
+	param set FW_LND_TLALT 15
+
+	param set FW_L1_PERIOD 25
+
+	param set FW_P_TC 0.4
+	param set FW_PR_FF 0.40
+	param set FW_PR_I 0.05
+	param set FW_PR_P 0.05
+
+	param set FW_R_TC 0.45
+	param set FW_RR_FF 0.40
+	param set FW_RR_I 0.132
+	param set FW_RR_P 0.085
+
+	param set FW_W_EN 1
+
+	param set MIS_LTRMIN_ALT 30
+	param set MIS_TAKEOFF_ALT 20
+	param set MIS_DIST_1WP 2500
+	param set MIS_DIST_WPS 10000
+
+	param set NAV_ACC_RAD 15
+	param set NAV_DLL_ACT 2
+	param set NAV_LOITER_RAD 50
+
+	param set RWTO_TKOFF 1
+	param set RWTO_MAX_PITCH 20
+	param set RWTO_MAX_ROLL 10
+	param set RWTO_PSP 8
+	param set RWTO_AIRSPD_SCL 1.8
+
+fi
+
+set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Standard VTOL
+#
+# @type Standard VTOL
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set FW_L1_PERIOD 12
+	param set FW_MAN_P_MAX 30
+	param set FW_PR_FF 0.2
+	param set FW_PR_I 0.4
+	param set FW_PR_P 0.9
+	param set FW_PSP_OFF 2
+	param set FW_P_LIM_MAX 32
+	param set FW_P_LIM_MIN -15
+	param set FW_RR_FF 0.1
+	param set FW_RR_P 0.3
+	param set FW_THR_CRUISE 0.25
+	param set FW_THR_MAX 0.6
+	param set FW_THR_MIN 0.05
+	param set FW_T_ALT_TC 2
+	param set FW_T_CLMB_MAX 8
+	param set FW_T_HRATE_FF 0.5
+	param set FW_T_SINK_MAX 2.7
+	param set FW_T_SINK_MIN 2.2
+	param set FW_T_TAS_TC 2
+
+	param set MC_ROLLRATE_P 0.3
+	param set MC_YAW_P 1.6
+
+	param set MIS_TAKEOFF_ALT 10
+
+	param set MPC_ACC_HOR_MAX 2
+	param set MPC_XY_P 0.8
+	param set MPC_XY_VEL_P_ACC 3
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_D_ACC 0.1
+
+	param set NAV_ACC_RAD 5
+	param set NAV_LOITER_RAD 80
+
+	param set VT_FWD_THRUST_EN 4
+	param set VT_F_TRANS_THR 0.75
+	param set VT_MOT_ID 1234
+	param set VT_FW_MOT_OFFID 1234
+	param set VT_B_TRANS_DUR 8
+	param set VT_TYPE 2
+
+fi
+
+set MAV_TYPE 22
+
+set MIXER_FILE etc/mixers-sitl/standard_vtol_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Quadrotor + Tailsitter
+#
+# @type VTOL Quad Tailsitter
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set FW_L1_PERIOD 12
+	param set FW_MAN_P_MAX 30
+	param set FW_PR_I 0.2
+	param set FW_PR_P 0.3
+	param set FW_PSP_OFF 2
+	param set FW_P_LIM_MAX 32
+	param set FW_P_LIM_MIN -15
+	param set FW_RR_P 0.3
+	param set FW_THR_CRUISE 0.33
+	param set FW_THR_MAX 0.6
+	param set FW_THR_MIN 0.05
+	param set FW_T_ALT_TC 2
+	param set FW_T_CLMB_MAX 8
+	param set FW_T_HRATE_FF 0.5
+	param set FW_T_SINK_MAX 2.7
+	param set FW_T_SINK_MIN 2.2
+	param set FW_T_TAS_TC 2
+
+	param set MC_ROLLRATE_P 0.3
+
+	param set MPC_ACC_HOR_MAX 2
+	param set MPC_XY_P 0.8
+	param set MPC_XY_VEL_P_ACC 3
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_D_ACC 0.1
+
+	param set NAV_ACC_RAD 5
+	param set NAV_LOITER_RAD 80
+
+	param set VT_F_TRANS_DUR 1.5
+	param set VT_F_TRANS_THR 0.7
+	param set VT_TYPE 0
+
+	param set WV_EN 0
+
+fi
+
+set MAV_TYPE 20
+
+set MIXER_FILE etc/mixers-sitl/quad_x_vtol.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name VTOL Tiltrotor
+#
+# @type VTOL Tiltrotor
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set FW_L1_PERIOD 12
+	param set FW_MAN_P_MAX 30
+	param set FW_PR_FF 0.2
+	param set FW_PR_I 0.4
+	param set FW_PR_P 0.9
+	param set FW_PSP_OFF 2
+	param set FW_P_LIM_MAX 32
+	param set FW_P_LIM_MIN -15
+	param set FW_RR_FF 0.1
+	param set FW_RR_P 0.3
+	param set FW_THR_CRUISE 0.38
+	param set FW_THR_MAX 0.6
+	param set FW_THR_MIN 0.05
+	param set FW_T_ALT_TC 2
+	param set FW_T_CLMB_MAX 8
+	param set FW_T_HRATE_FF 0.5
+	param set FW_T_SINK_MAX 2.7
+	param set FW_T_SINK_MIN 2.2
+	param set FW_T_TAS_TC 2
+
+	param set MC_YAW_P 1.6
+
+	param set MIS_TAKEOFF_ALT 10
+
+	param set MPC_ACC_HOR_MAX 2
+	param set MPC_XY_P 0.8
+	param set MPC_XY_VEL_P_ACC 3
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_D_ACC 0.1
+
+	param set NAV_ACC_RAD 5
+	param set NAV_LOITER_RAD 80
+
+	param set VT_B_TRANS_DUR 8
+	param set VT_FWD_THRUST_EN 4
+	param set VT_MOT_ID 1234
+	param set VT_TILT_TRANS 0.6
+	param set VT_TYPE 1
+
+fi
+
+set MAV_TYPE 21
+
+set MIXER_FILE etc/mixers-sitl/tiltrotor_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Standard VTOL
+#
+# @type Standard VTOL
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set FW_L1_PERIOD 12
+	param set FW_MAN_P_MAX 30
+	param set FW_PR_FF 0.2
+	param set FW_PR_I 0.4
+	param set FW_PR_P 0.9
+	param set FW_PSP_OFF 2
+	param set FW_P_LIM_MAX 32
+	param set FW_P_LIM_MIN -15
+	param set FW_RR_FF 0.1
+	param set FW_RR_P 0.3
+	param set FW_THR_CRUISE 0.25
+	param set FW_THR_MAX 0.6
+	param set FW_THR_MIN 0.05
+	param set FW_T_ALT_TC 2
+	param set FW_T_CLMB_MAX 8
+	param set FW_T_HRATE_FF 0.5
+	param set FW_T_SINK_MAX 2.7
+	param set FW_T_SINK_MIN 2.2
+	param set FW_T_TAS_TC 2
+
+	param set MC_ROLLRATE_P 0.3
+	param set MC_YAW_P 1.6
+
+	param set MIS_TAKEOFF_ALT 10
+
+	param set MPC_ACC_HOR_MAX 2
+	param set MPC_XY_P 0.8
+	param set MPC_XY_VEL_P_ACC 3
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_D_ACC 0.1
+
+	param set NAV_ACC_RAD 5
+	param set NAV_LOITER_RAD 80
+
+	param set VT_FWD_THRUST_EN 4
+	param set VT_F_TRANS_THR 0.75
+	param set VT_MOT_ID 1234
+	param set VT_FW_MOT_OFFID 1234
+	param set VT_B_TRANS_DUR 8
+	param set VT_TYPE 2
+
+	param set RC_MAP_AUX1 8
+	param set RC_MAP_AUX2 9
+	param set RC_MAP_AUX3 10
+fi
+
+set MAV_TYPE 22
+
+set MIXER_FILE etc/mixers-sitl/standard_vtol_sitl.main.mix
+set MIXER custom

+mixer append /dev/pwm_output0 etc/mixers-sitl/package_drop.aux.mix

+#!/bin/sh
+#
+# @name Rover
+#
+
+. ${R}etc/init.d/rc.rover_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set GND_L1_DIST 5
+	param set GND_L1_PERIOD 10
+	param set GND_SP_CTRL_MODE 1
+	param set GND_SPEED_D 0.001
+	param set GND_SPEED_I 3
+	param set GND_SPEED_IMAX 0.125
+	param set GND_SPEED_P 0.25
+	param set GND_SPEED_THR_SC 1
+	param set GND_SPEED_TRIM 4
+	param set GND_THR_CRUISE 0.3
+	param set GND_THR_MAX 0.5
+	param set GND_THR_MIN 0
+
+	param set MIS_LTRMIN_ALT 0.01
+	param set MIS_TAKEOFF_ALT 0.01
+	param set NAV_ACC_RAD 0.5
+	param set NAV_LOITER_RAD 2
+
+	param set CBRK_AIRSPD_CHK 162128
+
+	param set GND_MAX_ANG 0.6
+	param set GND_WHEEL_BASE 2.0
+
+fi
+
+set MAV_TYPE 10
+
+set MIXER_FILE etc/mixers-sitl/rover_ackermann_sitl.main.mix

+#!/bin/sh
+#
+# @name Aion Robotics R1 Rover
+# @type Rover
+# @class Rover
+
+. ${R}etc/init.d/rc.rover_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set GND_L1_DIST 5
+	param set GND_SP_CTRL_MODE 1
+	param set GND_SPEED_D 3
+	param set GND_SPEED_I 0.001
+	param set GND_SPEED_IMAX 0.125
+	param set GND_SPEED_P 0.25
+	param set GND_SPEED_THR_SC 1
+	param set GND_SPEED_TRIM 4
+	param set GND_THR_CRUISE 0.3
+	param set GND_THR_MAX 0.5
+	param set GND_THR_MIN 0
+
+	param set MIS_LTRMIN_ALT 0.01
+	param set MIS_TAKEOFF_ALT 0.01
+	param set NAV_ACC_RAD 0.5
+	param set NAV_LOITER_RAD 2
+
+	param set CBRK_AIRSPD_CHK 162128
+
+	param set GND_MAX_ANG 0.6
+	param set GND_WHEEL_BASE 2.0
+
+fi
+
+set MAV_TYPE 10
+
+set MIXER_FILE etc/mixers-sitl/rover_diff_sitl.main.mix

+#!/bin/sh
+#
+# @name ThunderFly TF-R1 UAV Rover
+# @type Rover
+# @class Rover
+#
+# @url https://github.com/ThunderFly-aerospace/TF-R1/
+# @maintainer ThunderFly s.r.o.
+#
+
+. ${R}etc/init.d/rc.rover_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set GND_L1_DIST 5
+	param set GND_SP_CTRL_MODE 1
+	param set GND_SPEED_D 3
+	param set GND_SPEED_I 0.001
+	param set GND_SPEED_IMAX 0.125
+	param set GND_SPEED_P 0.25
+	param set GND_SPEED_THR_SC 1
+	param set GND_SPEED_TRIM 15
+	param set GND_SPEED_MAX 25
+	param set GND_THR_CRUISE 0.3
+	param set GND_THR_MAX 0.5
+	param set GND_THR_MIN 0
+
+	param set MIS_LTRMIN_ALT 0.01
+	param set MIS_TAKEOFF_ALT 0.01
+	param set NAV_ACC_RAD 0.5
+	param set NAV_LOITER_RAD 2
+
+	param set CBRK_AIRSPD_CHK 162128
+
+	param set GND_MAX_ANG 0.6
+	param set GND_WHEEL_BASE 3.0
+
+fi
+
+set MAV_TYPE 10
+
+set MIXER_FILE etc/mixers-sitl/rover_ackermann_sitl.main.mix

+#!/bin/sh
+#
+# @name Boat
+#
+
+. ${R}etc/init.d/rc.boat_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set GND_L1_DIST 5
+	param set GND_L1_PERIOD 100
+	param set GND_SP_CTRL_MODE 1
+	param set GND_SPEED_D 0.001
+	param set GND_SPEED_I 8
+	param set GND_SPEED_IMAX 0.125
+	param set GND_SPEED_P 2
+	param set GND_SPEED_THR_SC 1
+	param set GND_SPEED_TRIM 1
+	param set GND_THR_CRUISE 0.85
+	param set GND_THR_MAX 1
+	param set GND_THR_MIN 0
+
+	param set MIS_LTRMIN_ALT 0.01
+	param set MIS_TAKEOFF_ALT 0.01
+	param set NAV_ACC_RAD 0.5
+	param set NAV_LOITER_RAD 2
+
+	param set CBRK_AIRSPD_CHK 162128
+
+	param set GND_MAX_ANG 0.6
+	param set GND_WHEEL_BASE 2.0
+
+fi
+
+set MAV_TYPE 11
+
+set MIXER_FILE etc/mixers-sitl/boat_sitl.main.mix

+#!/bin/sh
+#
+# @name ThunderFly TF-G1
+# ThunderFly TF-G1 autogyro airframe. Only for FlightGear simulator
+#
+# @type Autogyro
+# @class Autogyro
+#
+# @url https://github.com/ThunderFly-aerospace/TF-G1/
+#
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set EKF2_ARSP_THR 8
+	param set EKF2_FUSE_BETA 1
+	param set ASPD_STALL 10.0
+
+	param set FW_P_RMAX_NEG 20.0
+	param set FW_P_RMAX_POS 60.0
+	param set FW_W_RMAX 10
+	param set FW_W_EN 1
+
+	param set FW_PR_IMAX 0.4
+	param set FW_R_TC 0.4
+	param set FW_RR_FF 0.5
+	param set FW_RR_I 0.1
+	param set FW_RR_IMAX 0.2
+	param set FW_RR_P 0.08
+
+	param set MIS_LTRMIN_ALT 50
+	param set MIS_TAKEOFF_ALT 3
+
+	param set NAV_ACC_RAD 20
+	param set NAV_DLL_ACT 2
+	param set NAV_LOITER_RAD 100
+
+	param set RWTO_TKOFF 1
+
+	param set FW_ARSP_SCALE_EN 0
+
+	param set FW_AIRSPD_MAX 35
+	param set FW_AIRSPD_MIN 7
+	param set FW_AIRSPD_TRIM 15
+
+	param set FW_P_LIM_MAX 25
+	param set FW_P_LIM_MIN -5
+	param set FW_R_LIM 30
+
+	param set FW_MAN_P_MAX 30.0
+	param set FW_MAN_R_MAX 30.0
+
+	param set FW_THR_CRUISE 0.8
+	param set FW_THR_IDLE 0
+	param set COM_DISARM_PRFLT 0
+
+fi
+
+
+set MIXER_FILE etc/mixers-sitl/autogyro_sitl.main.mix
+set MIXER custom

+#!/bin/sh
+#
+# @name Cloudship
+# @type Airship
+# @class Airship
+#
+# @output MAIN1 thrust tilt
+# @output MAIN2 starboard thruster
+# @output MAIN3 port thruster
+# @output MAIN4 tail thruster
+
+. ${R}etc/init.d/rc.airship_defaults
+
+set MIXER cloudship
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Quadrotor SITL model for JSBSim
+#
+# @type Quadrotor Wide
+#
+# @maintainer Jaeyoung Lim <jaeyoung@auterion.com>
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER quad_w

+#!/bin/sh
+#
+# @name Hexacopter SITL model for JSBSim
+#
+# @type Hexarotor x
+#
+# @maintainer Jaeyoung Lim <jaeyoung@auterion.com>
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set MC_PITCHRATE_P 0.1
+	param set MC_PITCHRATE_I 0.05
+	param set MC_PITCH_P 6.0
+	param set MC_ROLLRATE_P 0.15
+	param set MC_ROLLRATE_I 0.1
+	param set MC_ROLL_P 6.0
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_P_ACC 3
+
+	param set RTL_DESCEND_ALT 10
+
+	param set TRIG_INTERFACE 3
+	param set TRIG_MODE 4
+	param set MNT_MODE_IN 4
+	param set MNT_DO_STAB 2
+fi
+
+set MAV_TYPE 13
+
+set MIXER hexa_x

+#!/bin/sh
+#
+# @name Typhoon H480 SITL
+#
+# @type Hexarotor x
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+if [ $AUTOCNF = yes ]
+then
+	param set MC_PITCHRATE_P 0.0800
+	param set MC_PITCHRATE_I 0.0400
+	param set MC_PITCHRATE_D 0.0010
+	param set MC_PITCH_P 9.0
+	param set MC_ROLLRATE_P 0.0800
+	param set MC_ROLLRATE_I 0.0400
+	param set MC_ROLLRATE_D 0.0010
+	param set MC_ROLL_P 9.0
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_P_ACC 3
+
+	param set RTL_DESCEND_ALT 10
+
+	param set TRIG_INTERFACE 3
+	param set TRIG_MODE 4
+	param set MNT_MODE_IN 4
+	param set MNT_MODE_OUT 2
+	param set MAV_PROTO_VER 2
+fi
+
+set MAV_TYPE 13
+
+set MIXER hexa_x

+
+mixer append /dev/pwm_output0 etc/mixers/mount_legs.aux.mix
+
+mavlink start -x -u 14558 -r 4000 -f -m onboard -o 14530 -p
+
+# shellcheck disable=SC2154
+mavlink stream -r 10 -s MOUNT_ORIENTATION -u $udp_gcs_port_local
+# shellcheck disable=SC2154
+mavlink stream -r 50 -s ATTITUDE_QUATERNION -u $udp_offboard_port_local
+mavlink stream -r 10 -s MOUNT_ORIENTATION -u $udp_offboard_port_local

+#!/bin/sh
+#
+# @name Typhoon H480 SITL
+#
+# @type Hexarotor x
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+. ${R}etc/init.d/rc.ctrlalloc
+
+if [ $AUTOCNF = yes ]
+then
+	param set MPC_XY_VEL_I_ACC 4
+	param set MPC_XY_VEL_P_ACC 3
+
+	param set RTL_DESCEND_ALT 10
+	param set RTL_LAND_DELAY 0
+
+	param set TRIG_INTERFACE 3
+	param set TRIG_MODE 4
+	param set MNT_MODE_IN 0
+	param set MAV_PROTO_VER 2
+
+	param set MPC_USE_HTE 0
+
+	param set VM_MASS 2.66
+	param set VM_INERTIA_XX 0.06
+	param set VM_INERTIA_YY 0.06
+	param set VM_INERTIA_ZZ 0.10
+
+	param set CA_AIRFRAME 0
+	param set CA_METHOD 1
+	param set CA_ACT0_MIN 0.0
+	param set CA_ACT1_MIN 0.0
+	param set CA_ACT2_MIN 0.0
+	param set CA_ACT3_MIN 0.0
+	param set CA_ACT4_MIN 0.0
+	param set CA_ACT5_MIN 0.0
+	param set CA_ACT0_MAX 1.0
+	param set CA_ACT1_MAX 1.0
+	param set CA_ACT2_MAX 1.0
+	param set CA_ACT3_MAX 1.0
+	param set CA_ACT4_MAX 1.0
+	param set CA_ACT5_MAX 1.0
+
+	param set CA_MC_R0_PX 0.0
+	param set CA_MC_R0_PY 1.0
+	param set CA_MC_R0_CT 9.5
+	param set CA_MC_R0_KM -0.05
+	param set CA_MC_R1_PX 0.0
+	param set CA_MC_R1_PY -1.0
+	param set CA_MC_R1_CT 9.5
+	param set CA_MC_R1_KM 0.05
+	param set CA_MC_R2_PX 0.866025
+	param set CA_MC_R2_PY -0.5
+	param set CA_MC_R2_CT 9.5
+	param set CA_MC_R2_KM -0.05
+	param set CA_MC_R3_PX -0.866025
+	param set CA_MC_R3_PY 0.5
+	param set CA_MC_R3_CT 9.5
+	param set CA_MC_R3_KM 0.05
+	param set CA_MC_R4_PX 0.866025
+	param set CA_MC_R4_PY 0.5
+	param set CA_MC_R4_CT 9.5
+	param set CA_MC_R4_KM 0.05
+	param set CA_MC_R5_PX -0.866025
+	param set CA_MC_R5_PY -0.5
+	param set CA_MC_R5_CT 9.5
+	param set CA_MC_R5_KM -0.05
+fi
+
+set MAV_TYPE 13
+
+# set MIXER hexa_x
+set MIXER direct

+
+mixer append /dev/pwm_output0 etc/mixers/mount_legs.aux.mix
+
+mavlink start -x -u 14558 -r 4000 -f -m onboard -o 14530 -p
+
+# shellcheck disable=SC2154
+mavlink stream -r 10 -s MOUNT_ORIENTATION -u $udp_gcs_port_local
+# shellcheck disable=SC2154
+mavlink stream -r 50 -s ATTITUDE_QUATERNION -u $udp_offboard_port_local
+mavlink stream -r 10 -s MOUNT_ORIENTATION -u $udp_offboard_port_local

+############################################################################
+#
+#   Copyright (c) 2020 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+px4_add_romfs_files(
+	10016_iris
+	10017_iris_ctrlalloc
+	10018_iris_foggy_lidar
+	10020_if750a
+	10030_px4vision
+	1010_iris_opt_flow
+	1010_iris_opt_flow.post
+	1011_iris_irlock
+	1012_iris_rplidar
+	1013_iris_vision
+	1013_iris_vision.post
+	1014_solo
+	1015_iris_obs_avoid
+	1015_iris_obs_avoid.post
+	1016_iris_rtps
+	1016_iris_rtps.post
+	1017_iris_opt_flow_mockup
+	1018_iris_vision_velocity
+	1019_iris_dual_gps
+	1020_uuv_generic
+	1021_uuv_hippocampus
+	1022_uuv_bluerov2_heavy
+	1030_plane
+	1031_plane_cam
+	1032_plane_catapult
+	1033_plane_lidar
+	1033_rascal
+	1034_rascal-electric
+	1035_techpod
+	1036_malolo
+	1040_standard_vtol
+	1041_tailsitter
+	1042_tiltrotor
+	1043_standard_vtol_drop
+	1043_standard_vtol_drop.post
+	1060_rover
+	1061_r1_rover
+	1062_tf-r1
+	1070_boat
+	3010_quadrotor_x
+	3011_hexarotor_x
+	17001_tf-g1
+	2507_cloudship
+	6011_typhoon_h480
+	6011_typhoon_h480.post
+	6012_typhoon_ctrlalloc
+	6012_typhoon_ctrlalloc.post
+)

+#!/bin/sh
+
+# EKF2 replay script
+
+# shellcheck disable=SC2154
+if [ ! -f ${replay} ]; then
+	echo "Invalid replay log file ${replay}"
+	exit 1
+fi
+
+if [ ! -f replay_params.txt ]; then
+	echo "Creating $(pwd)/replay_params.txt"
+	ulog_params -i "${replay}" -d ' ' | grep -e '^EKF2' > replay_params.txt
+fi
+
+publisher_rules_file="orb_publisher.rules"
+cat <<EOF > "$publisher_rules_file"
+restrict_topics: sensor_combined, vehicle_gps_position, vehicle_land_detected
+module: replay
+ignore_others: false
+EOF
+
+param set SDLOG_DIRS_MAX 7
+
+# apply all params before ekf starts, as some params cannot be changed after startup
+replay tryapplyparams
+ekf2 start -r
+logger start -f -t -b 1000 -p vehicle_attitude
+replay start

+#!/bin/sh
+
+# PX4 commands need the 'px4-' prefix in bash.
+# (px4-alias.sh is expected to be in the PATH)
+# shellcheck disable=SC1091
+. px4-alias.sh
+
+SCRIPT_DIR="$(CDPATH='' cd -- "$(dirname -- "$0")" && pwd)"
+
+#
+# Main SITL startup script
+#
+
+# check for ekf2 replay
+# shellcheck disable=SC2154
+if [ "$replay_mode" = "ekf2" ]
+then
+	. ${R}etc/init.d-posix/rc.replay
+	exit 0
+fi
+
+# initialize script variables
+set AUX_MODE                    none
+set AUX_BANK2			none
+set IO_PRESENT                  no
+set MAV_TYPE                    none
+set MIXER                       none
+set MIXER_AUX                   none
+set MIXER_FILE                  none
+set OUTPUT_MODE                 sim
+set EXTRA_MIXER_MODE            none
+set PWM_OUT                     none
+set SDCARD_MIXERS_PATH          etc/mixers
+set USE_IO                      no
+set VEHICLE_TYPE                none
+set LOGGER_ARGS                 ""
+set LOGGER_BUF                  1000
+
+set RUN_MINIMAL_SHELL           no
+
+# Use the variable set by sitl_run.sh to choose the model settings.
+if [ "$PX4_SIM_MODEL" = "shell" ]; then
+	set RUN_MINIMAL_SHELL yes
+else
+	# Find the matching Autostart ID (file name has the form: [0-9]+_${PX4_SIM_MODEL})
+	# TODO: unify with rc.autostart generation
+	# shellcheck disable=SC2012
+	REQUESTED_AUTOSTART=$(ls "$SCRIPT_DIR/airframes" | sed -n 's/^\([0-9][0-9]*\)_'${PX4_SIM_MODEL}'$/\1/p')
+	if [ -z "$REQUESTED_AUTOSTART" ]; then
+		echo "Error: Unknown model $PX4_SIM_MODEL (not found by name on $SCRIPT_DIR/airframes)"
+		exit 1
+	else
+		echo "Info: found model autostart file as SYS_AUTOSTART=$REQUESTED_AUTOSTART"
+	fi
+fi
+
+# Load parameters
+set PARAM_FILE eeprom/parameters_"$REQUESTED_AUTOSTART"
+param select $PARAM_FILE
+
+if [ -f $PARAM_FILE ]
+then
+	if param load
+	then
+		echo "[param] Loaded: $PARAM_FILE"
+	else
+		echo "[param] FAILED loading $PARAM_FILE"
+	fi
+else
+	echo "[param] parameter file not found, creating $PARAM_FILE"
+fi
+
+# exit early when the minimal shell is requested
+[ $RUN_MINIMAL_SHELL = yes ] && exit 0
+
+
+# Use environment variable PX4_ESTIMATOR to choose estimator.
+if [ "$PX4_ESTIMATOR" = "q" ]; then
+	param set SYS_MC_EST_GROUP 3
+elif [ "$PX4_ESTIMATOR" = "ekf2" ]; then
+	param set SYS_MC_EST_GROUP 2
+elif [ "$PX4_ESTIMATOR" = "lpe" ]; then
+	param set SYS_MC_EST_GROUP 1
+elif [ "$PX4_ESTIMATOR" = "inav" ]; then
+	param set SYS_MC_EST_GROUP 0
+fi
+
+if param compare SYS_AUTOSTART $REQUESTED_AUTOSTART
+then
+	set AUTOCNF no
+else
+	set AUTOCNF yes
+	param set SYS_AUTOCONFIG 1
+fi
+
+if param compare SYS_AUTOCONFIG 1
+then
+	set AUTOCNF yes
+
+	# Wipe out params except RC*, flight modes, total flight time, accel cal, gyro cal, next flight UUID
+	param reset_all SYS_AUTOSTART SYS_AUTOCONFIG RC* COM_FLTMODE* LND_FLIGHT_T_* TC_* CAL_ACC* CAL_GYRO* COM_FLIGHT_UUID
+fi
+
+# multi-instance setup
+# shellcheck disable=SC2154
+param set MAV_SYS_ID $((px4_instance+1))
+simulator_tcp_port=$((4560+px4_instance))
+udp_offboard_port_local=$((14580+px4_instance))
+udp_offboard_port_remote=$((14540+px4_instance))
+[ $px4_instance -gt 9 ] && udp_offboard_port_remote=14549 # use the same ports for more than 10 instances to avoid port overlaps
+udp_onboard_payload_port_local=$((14280+px4_instance))
+udp_onboard_payload_port_remote=$((14030+px4_instance))
+udp_onboard_gimbal_port_local=$((13030+px4_instance))
+udp_onboard_gimbal_port_remote=$((13280+px4_instance))
+udp_gcs_port_local=$((18570+px4_instance))
+
+if [ $AUTOCNF = yes ]
+then
+	param set SYS_AUTOSTART $REQUESTED_AUTOSTART
+
+	param set CAL_ACC0_ID  1310988 # 1310988: DRV_IMU_DEVTYPE_SIM, BUS: 1, ADDR: 1, TYPE: SIMULATION
+	param set CAL_GYRO0_ID 1310988 # 1310988: DRV_IMU_DEVTYPE_SIM, BUS: 1, ADDR: 1, TYPE: SIMULATION
+	param set CAL_ACC1_ID  1310996 # 1310996: DRV_IMU_DEVTYPE_SIM, BUS: 2, ADDR: 1, TYPE: SIMULATION
+	param set CAL_GYRO1_ID 1310996 # 1310996: DRV_IMU_DEVTYPE_SIM, BUS: 2, ADDR: 1, TYPE: SIMULATION
+	param set CAL_ACC2_ID  1311004 # 1311004: DRV_IMU_DEVTYPE_SIM, BUS: 3, ADDR: 1, TYPE: SIMULATION
+	param set CAL_GYRO2_ID 1311004 # 1311004: DRV_IMU_DEVTYPE_SIM, BUS: 3, ADDR: 1, TYPE: SIMULATION
+
+	param set CAL_MAG0_ID 197388
+	param set CAL_MAG1_ID 197644
+
+	param set SENS_BOARD_X_OFF 0.000001
+	param set SENS_DPRES_OFF 0.001
+
+	param set SYS_RESTART_TYPE 2
+fi
+
+param set-default BAT_N_CELLS 4
+
+param set-default CBRK_AIRSPD_CHK 0
+param set-default CBRK_SUPPLY_CHK 894281
+
+# disable check, no CPU load reported on posix yet
+param set-default COM_CPU_MAX -1
+
+# Don't require RC calibration and configuration
+param set-default COM_RC_IN_MODE 1
+
+# Speedup SITL startup
+param set-default EKF2_REQ_GPS_H 0.5
+
+# Multi-EKF
+param set-default EKF2_MULTI_IMU 3
+param set-default SENS_IMU_MODE 0
+param set-default EKF2_MULTI_MAG 2
+param set-default SENS_MAG_MODE 0
+
+param set-default IMU_GYRO_FFT_EN 1
+
+# By default log from boot until first disarm.
+param set-default SDLOG_MODE 1
+# enable default, estimator replay and vision/avoidance logging profiles
+param set-default SDLOG_PROFILE 131
+param set-default SDLOG_DIRS_MAX 7
+
+param set-default TRIG_INTERFACE 3
+
+# Adapt timeout parameters if simulation runs faster or slower than realtime.
+if [ -n "$PX4_SIM_SPEED_FACTOR" ]; then
+	COM_DL_LOSS_T_LONGER=$(echo "$PX4_SIM_SPEED_FACTOR * 10" | bc)
+	echo "COM_DL_LOSS_T set to $COM_DL_LOSS_T_LONGER"
+	param set COM_DL_LOSS_T $COM_DL_LOSS_T_LONGER
+
+	COM_RC_LOSS_T_LONGER=$(echo "$PX4_SIM_SPEED_FACTOR * 0.5" | bc)
+	echo "COM_RC_LOSS_T set to $COM_RC_LOSS_T_LONGER"
+	param set COM_RC_LOSS_T $COM_RC_LOSS_T_LONGER
+
+	COM_OF_LOSS_T_LONGER=$(echo "$PX4_SIM_SPEED_FACTOR * 0.5" | bc)
+	echo "COM_OF_LOSS_T set to $COM_OF_LOSS_T_LONGER"
+	param set COM_OF_LOSS_T $COM_OF_LOSS_T_LONGER
+fi
+
+# Autostart ID
+autostart_file=''
+# shellcheck disable=SC2231
+for f in ${R}etc/init.d-posix/airframes/"$(param show -q SYS_AUTOSTART)"_*
+do
+	filename=$(basename "$f")
+	case "$filename" in
+		*\.*)
+			# ignore files that contain a dot (e.g. <vehicle>.post)
+			;;
+		*)
+			autostart_file="$f"
+			;;
+	esac
+done
+if [ ! -e "$autostart_file" ]; then
+	echo "Error: no autostart file found ($autostart_file)"
+	exit 1
+fi
+
+. "$autostart_file"
+
+#
+# If autoconfig parameter was set, reset it and save parameters.
+#
+if [ $AUTOCNF = yes ]
+then
+	param set SYS_AUTOCONFIG 0
+fi
+
+# Simulator IMU data provided at 250 Hz
+param set IMU_INTEG_RATE 250
+
+dataman start
+# only start the simulator if not in replay mode, as both control the lockstep time
+if ! replay tryapplyparams
+then
+	simulator start -c $simulator_tcp_port
+fi
+load_mon start
+battery_simulator start
+tone_alarm start
+rc_update start
+sensors start
+commander start
+navigator start
+
+
+if param greater -s MNT_MODE_IN -1
+then
+	vmount start
+fi
+
+if param greater -s TRIG_MODE 0
+then
+	camera_trigger start
+	camera_feedback start
+fi
+
+if param compare -s IMU_GYRO_FFT_EN 1
+then
+	gyro_fft start
+fi
+
+if param compare -s IMU_GYRO_CAL_EN 1
+then
+	gyro_calibration start
+fi
+
+# Configure vehicle type specific parameters.
+# Note: rc.vehicle_setup is the entry point for rc.interface,
+#       rc.fw_apps, rc.mc_apps, rc.rover_apps, and rc.vtol_apps.
+#
+. ${R}etc/init.d/rc.vehicle_setup
+
+if [ -e etc/init.d-posix/rc.mavlink_override ]
+then
+	echo "Running non-default mavlink config rc.mavlink_override"
+	sh etc/init.d-posix/rc.mavlink_override
+else
+	# GCS link
+	mavlink start -x -u $udp_gcs_port_local -r 4000000 -f
+	mavlink stream -r 50 -s POSITION_TARGET_LOCAL_NED -u $udp_gcs_port_local
+	mavlink stream -r 50 -s LOCAL_POSITION_NED -u $udp_gcs_port_local
+	mavlink stream -r 50 -s GLOBAL_POSITION_INT -u $udp_gcs_port_local
+	mavlink stream -r 50 -s ATTITUDE -u $udp_gcs_port_local
+	mavlink stream -r 50 -s ATTITUDE_QUATERNION -u $udp_gcs_port_local
+	mavlink stream -r 50 -s ATTITUDE_TARGET -u $udp_gcs_port_local
+	mavlink stream -r 50 -s SERVO_OUTPUT_RAW_0 -u $udp_gcs_port_local
+	mavlink stream -r 20 -s RC_CHANNELS -u $udp_gcs_port_local
+	mavlink stream -r 10 -s OPTICAL_FLOW_RAD -u $udp_gcs_port_local
+
+	# API/Offboard link
+	mavlink start -x -u $udp_offboard_port_local -r 4000000 -f -m onboard -o $udp_offboard_port_remote
+
+	# Onboard link to camera
+	mavlink start -x -u $udp_onboard_payload_port_local -r 4000 -f -m onboard -o $udp_onboard_payload_port_remote
+
+	# Onboard link to gimbal
+	mavlink start -x -u $udp_onboard_gimbal_port_local -r 400000 -m gimbal -o $udp_onboard_gimbal_port_remote
+fi
+
+# execute autostart post script if any
+[ -e "$autostart_file".post ] && . "$autostart_file".post
+
+# Run script to start logging
+if param compare SYS_MC_EST_GROUP 2
+then
+	set LOGGER_ARGS "-p ekf2_timestamps"
+else
+	set LOGGER_ARGS "-p vehicle_attitude"
+fi
+. ${R}etc/init.d/rc.logging
+
+mavlink boot_complete
+replay trystart

+############################################################################
+#
+#   Copyright (c) 2018 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+add_subdirectory(airframes)
+
+px4_add_romfs_files(
+	rc.airship_apps
+	rc.airship_defaults
+	rc.balloon_apps
+	rc.balloon_defaults
+	rc.boat_defaults
+	rc.fw_apps
+	rc.fw_defaults
+	rc.interface
+	rc.io
+	rc.logging
+	rc.mc_apps
+	rc.mc_defaults
+	rcS
+	rc.sensors
+	rc.thermal_cal
+	rc.rover_apps
+	rc.rover_defaults
+	rc.uuv_apps
+	rc.uuv_defaults
+	rc.vehicle_setup
+	rc.vtol_apps
+	rc.vtol_defaults
+	rc.ctrlalloc
+)

+#!/bin/sh
+#
+# @name HILStar (XPlane)
+#
+# @type Simulation
+# @class Plane
+#
+# @output MAIN1 aileron
+# @output MAIN2 elevator
+# @output MAIN3 rudder
+# @output MAIN4 throttle
+# @output MAIN5 flaps
+# @output MAIN6 gear
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+
+param set-default BAT_N_CELLS 3
+
+param set-default FW_AIRSPD_MAX 20
+param set-default FW_AIRSPD_MIN 12
+param set-default FW_AIRSPD_TRIM 14
+param set-default FW_R_TC 0.3
+param set-default FW_P_TC 0.3
+param set-default FW_L1_DAMPING 0.74
+param set-default FW_L1_PERIOD 16
+param set-default FW_LND_ANG 15
+param set-default FW_LND_FLALT 5
+param set-default FW_LND_HHDIST 15
+param set-default FW_LND_HVIRT 13
+param set-default FW_LND_TLALT 5
+param set-default FW_THR_LND_MAX 0
+param set-default FW_PR_FF 0.35
+param set-default FW_PR_I 0.1
+param set-default FW_PR_IMAX 0.4
+param set-default FW_PR_P 0.2
+param set-default FW_RR_FF 0.6
+param set-default FW_RR_I 0.1
+param set-default FW_RR_IMAX 0.2
+param set-default FW_RR_P 0.3
+
+param set-default RWTO_TKOFF 1
+
+
+param set SYS_HITL 1
+
+# disable some checks to allow to fly
+# - with usb
+param set-default CBRK_USB_CHK 197848
+# - without real battery
+param set-default CBRK_SUPPLY_CHK 894281
+# - without safety switch
+param set-default COM_PREARM_MODE 0
+param set-default CBRK_IO_SAFETY 22027
+
+set MIXER AERT

+#!/bin/sh
+#
+# @name Team Blacksheep Discovery
+#
+# @type Quadrotor Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 feed-through of RC AUX1 channel
+# @output MAIN6 feed-through of RC AUX2 channel
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+# @output AUX4 feed-through of RC FLAPS channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+
+param set-default MC_ROLL_P 6.5
+param set-default MC_ROLLRATE_P 0.1
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_ROLLRATE_D 0.0017
+param set-default MC_PITCH_P 6.5
+param set-default MC_PITCHRATE_P 0.14
+param set-default MC_PITCHRATE_I 0.1
+param set-default MC_PITCHRATE_D 0.0025
+param set-default MC_YAW_P 2.8
+param set-default MC_YAWRATE_P 0.28
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+set MIXER quad_w
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name 3DR Iris Quadrotor
+#
+# @type Quadrotor Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+# @output AUX4 feed-through of RC FLAPS channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+
+# TODO tune roll/pitch separately
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.15
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.15
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_YAW_P 2.5
+param set-default MC_YAWRATE_P 0.25
+param set-default MC_YAWRATE_I 0.25
+param set-default MC_YAWRATE_D 0
+
+param set-default BAT_V_DIV 12.27559
+param set-default BAT_A_PER_V 15.39103
+set MIXER quad_w
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Steadidrone QU4D
+#
+# @type Quadrotor Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 feed-through of RC AUX1 channel
+# @output MAIN6 feed-through of RC AUX2 channel
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+# @output AUX4 feed-through of RC FLAPS channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+
+param set-default BAT_N_CELLS 4
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.13
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.19
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_YAW_P 4
+param set-default MC_YAWRATE_P 0.2
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+set MIXER quad_w
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Team Blacksheep Discovery Endurance
+#
+# @type Quadrotor Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 feed-through of RC AUX1 channel
+# @output MAIN6 feed-through of RC AUX2 channel
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+# @output AUX4 feed-through of RC FLAPS channel
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+
+param set-default BAT_N_CELLS 6
+param set-default BAT_V_EMPTY 3.5
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.08
+param set-default MC_ROLLRATE_I 0.02
+param set-default MC_ROLLRATE_D 0.003
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.13
+param set-default MC_PITCHRATE_I 0.02
+param set-default MC_PITCHRATE_D 0.005
+param set-default MC_YAW_P 2.8
+param set-default MC_YAWRATE_P 0.2
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+
+param set-default MPC_XY_VEL_MAX 2
+
+param set-default PWM_MAIN_MIN 1080
+set MIXER quad_w
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name HIL Quadcopter X
+#
+# @type Simulation
+# @class Copter
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER quad_x
+set PWM_OUT 1234
+
+param set SYS_HITL 1
+
+# disable some checks to allow to fly
+# - with usb
+param set-default CBRK_USB_CHK 197848
+# - without real battery
+param set-default CBRK_SUPPLY_CHK 894281
+# - without safety switch
+param set-default COM_PREARM_MODE 0
+param set-default CBRK_IO_SAFETY 22027

+#!/bin/sh
+#
+# @name HIL Standard VTOL QuadPlane
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Roman Bapst <roman@auterion.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default BAT_N_CELLS 3
+
+param set-default COM_RC_IN_MODE 1
+
+param set-default EKF2_AID_MASK 1
+param set-default EKF2_ANGERR_INIT 0.01
+param set-default EKF2_GBIAS_INIT 0.01
+param set-default EKF2_HGT_MODE 0
+param set-default EKF2_MAG_TYPE 1
+
+param set-default FW_AIRSPD_MAX 25
+param set-default FW_AIRSPD_MIN 14
+param set-default FW_AIRSPD_TRIM 16
+
+param set-default MC_PITCH_P 6
+param set-default MC_PITCHRATE_P 0.2
+param set-default MC_ROLL_P 6
+param set-default MC_ROLLRATE_P 0.3
+param set-default MIS_LTRMIN_ALT 10
+param set-default MIS_TAKEOFF_ALT 10
+param set-default MIS_YAW_TMT 10
+
+param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_THR_MIN 0.1
+param set-default MPC_TKO_SPEED 1
+param set-default MPC_XY_P 0.8
+param set-default MPC_XY_VEL_D_ACC 0.1
+param set-default MPC_XY_VEL_I_ACC 4
+param set-default MPC_XY_VEL_P_ACC 3
+param set-default MPC_Z_VEL_P_ACC 12
+param set-default MPC_Z_VEL_I_ACC 3
+param set-default MPC_Z_VEL_MAX_DN 1.5
+
+param set-default NAV_ACC_RAD 5
+param set-default NAV_DLL_ACT 2
+param set-default NAV_LOITER_RAD 80
+
+param set-default RTL_DESCEND_ALT 10
+param set-default RTL_RETURN_ALT 30
+
+param set-default SDLOG_DIRS_MAX 7
+param set-default SYS_RESTART_TYPE 2
+
+param set-default VT_F_TRANS_THR 0.75
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_TYPE 2
+
+
+param set SYS_HITL 1
+
+# disable some checks to allow to fly
+# - with usb
+param set-default CBRK_USB_CHK 197848
+# - without real battery
+param set-default CBRK_SUPPLY_CHK 894281
+# - without safety switch
+param set-default COM_PREARM_MODE 0
+param set-default CBRK_IO_SAFETY 22027
+
+set MAV_TYPE 22
+
+set MIXER standard_vtol_hitl
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Generic Hexarotor coaxial geometry
+#
+# @type Hexarotor Coaxial
+# @class Copter
+#
+# @output MAIN1 front right top, CW; angle:60; direction:CW
+# @output MAIN2 front right bottom, CCW; angle:60; direction:CCW
+# @output MAIN3 back top, CW; angle:180; direction:CW
+# @output MAIN4 back bottom, CCW; angle:180; direction:CCW
+# @output MAIN5 front left top, CW; angle:-60; direction:CW
+# @output MAIN6 front left bottom, CCW;angle:-60; direction:CCW
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER hexa_cox
+
+# Need to set all 8 channels
+set PWM_OUT 12345678

+#!/bin/sh
+#
+# @name SIH Quadcopter X
+#
+# @type Simulation
+# @class Copter
+#
+# @maintainer Romain Chiappinelli <romain.chiap@gmail.com>
+#
+# @board px4_fmu-v2 exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER quad_x
+set PWM_OUT 1234
+
+# set SYS_HITL to 2 to start the SIH and avoid sensors startup
+param set SYS_HITL 2
+
+# disable some checks to allow to fly:
+# - with usb
+param set-default CBRK_USB_CHK 197848
+# - without real battery
+param set-default CBRK_SUPPLY_CHK 894281
+# - without safety switch
+param set-default COM_PREARM_MODE 0
+param set-default CBRK_IO_SAFETY 22027

+#!/bin/sh
+#
+# @name Generic 10" Octo coaxial geometry
+#
+# @type Octorotor Coaxial
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 motor 5
+# @output MAIN6 motor 6
+# @output MAIN7 motor 7
+# @output MAIN8 motor 8
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER octo_cox
+
+set PWM_OUT 12345678

+#!/bin/sh
+#
+# @name Steadidrone MAVRIK
+#
+# @type Octo Coax Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 motor 5
+# @output MAIN6 motor 6
+# @output MAIN7 motor 7
+# @output MAIN8 motor 8
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+
+param set-default MC_PITCH_P 4
+param set-default MC_PITCHRATE_P 0.24
+param set-default MC_PITCHRATE_I 0.09
+param set-default MC_PITCHRATE_D 0.013
+param set-default MC_PITCHRATE_MAX 180
+
+param set-default MC_ROLL_P 4
+param set-default MC_ROLLRATE_P 0.16
+param set-default MC_ROLLRATE_I 0.07
+param set-default MC_ROLLRATE_D 0.009
+param set-default MC_ROLLRATE_MAX 180
+
+param set-default MC_YAW_P 3
+param set-default MC_YAWRATE_P 0.2
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+
+param set-default MPC_HOLD_MAX_XY 0.25
+param set-default MPC_THR_MIN 0.15
+param set-default MPC_Z_VEL_MAX_DN 2
+
+param set-default BAT_N_CELLS 4
+set MIXER octo_cox_w
+
+set PWM_OUT 12345678

+#!/bin/sh
+#
+# @name Generic Quadplane VTOL
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output AUX1 Aileron 1
+# @output AUX2 Aileron 2
+# @output AUX3 Elevator
+# @output AUX4 Rudder
+# @output AUX5 Throttle
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_AUX_DIS5 950
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_TYPE 2
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+set MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_AAERT
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Caipiroshka Duo Tailsitter
+#
+# @type VTOL Duo Tailsitter
+# @class VTOL
+#
+# @output MAIN1 motor right
+# @output MAIN2 motor left
+# @output MAIN5 elevon right
+# @output MAIN6 elevon left
+#
+# @maintainer Roman Bapst <roman@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default MAV_TYPE 19
+
+param set-default MC_ROLL_P 6
+param set-default MC_ROLLRATE_P 0.12
+param set-default MC_ROLLRATE_I 0.002
+param set-default MC_ROLLRATE_D 0.003
+param set-default MC_ROLLRATE_FF 0
+
+param set-default MC_PITCH_P 4.5
+param set-default MC_PITCHRATE_P 0.3
+param set-default MC_PITCHRATE_I 0.002
+param set-default MC_PITCHRATE_D 0.003
+param set-default MC_PITCHRATE_FF 0
+
+param set-default MC_YAW_P 3.8
+param set-default MC_YAWRATE_P 0.22
+param set-default MC_YAWRATE_I 0.02
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+
+param set-default VT_IDLE_PWM_MC  1080
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_MOT_ID 12
+param set-default VT_TYPE 0
+set MAV_TYPE 19
+
+set MIXER vtol_tailsitter_duo
+
+set PWM_OUT 123456

+#!/bin/sh
+#
+# @name BirdsEyeView Aerobotics FireFly6
+# @type VTOL Tiltrotor
+# @class VTOL
+#
+# @maintainer Roman Bapst <roman@uaventure.com>
+#
+# @output MAIN1 Front right motor bottom
+# @output MAIN2 Front right motor top
+# @output MAIN3 Back motor bottom
+# @output MAIN4 Back motor top
+# @output MAIN5 Front left motor bottom
+# @output MAIN6 Front left motor top
+# @output AUX1 Tilt servo
+# @output AUX2 Elevon 1
+# @output AUX3 Elevon 2
+# @output AUX4 Gear
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.19
+param set-default MC_ROLLRATE_I 0.002
+param set-default MC_ROLLRATE_D 0.005
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.14
+param set-default MC_PITCHRATE_I 0.002
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_YAW_P 4
+param set-default MC_YAWRATE_P 0.22
+param set-default MC_YAWRATE_I 0.02
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_FW_MOT_OFFID 34
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_MOT_ID 123456
+param set-default VT_FW_MOT_OFFID 56
+param set-default VT_TILT_MC 0.08
+param set-default VT_TILT_TRANS 0.5
+param set-default VT_TILT_FW 0.9
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_TYPE 1
+set MAV_TYPE 21
+
+set MIXER firefly6
+set MIXER_AUX firefly6
+
+set PWM_OUT 12345678

+#!/bin/sh
+#
+# @name Quadrotor X Tailsitter
+#
+# @type VTOL Quad Tailsitter
+# @class VTOL
+#
+# @maintainer Roman Bapst <roman@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_MAIN_MAX 2000
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_MOT_ID 1234
+param set-default VT_IDLE_PWM_MC  1080
+param set-default VT_TYPE 0
+param set-default VT_ELEV_MC_LOCK 1
+set MAV_TYPE 20
+
+set MIXER quad_x_vtol
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Quadrotor + Tailsitter
+#
+# @type VTOL Quad Tailsitter
+# @class VTOL
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 4
+# @output MAIN4 motor 5
+# @output MAIN5 elevon left
+# @output MAIN6 elevon right
+# @output MAIN7 canard surface
+# @output MAIN8 rudder
+#
+# @maintainer Roman Bapst <roman@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_MAIN_MAX 2000
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_IDLE_PWM_MC  1080
+param set-default VT_TYPE 0
+param set-default VT_ELEV_MC_LOCK 1
+set MAV_TYPE 20
+
+set MIXER quad_+_vtol
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Fun Cub Quad VTOL
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output AUX1 Aileron 1
+# @output AUX2 Aileron 2
+# @output AUX3 Elevator
+# @output AUX4 Rudder
+# @output AUX5 Throttle
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_AUX_DIS5 950
+
+param set-default PWM_MAIN_RATE 400
+
+param set-default MC_ROLL_P 6
+param set-default MC_ROLLRATE_P 0.17
+param set-default MC_ROLLRATE_I 0.002
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_PITCH_P 6
+param set-default MC_PITCHRATE_P 0.19
+param set-default MC_PITCHRATE_I 0.002
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_YAW_P 2.8
+param set-default MC_YAWRATE_P 0.22
+param set-default MC_YAWRATE_I 0.02
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+param set-default MC_YAWRATE_MAX 40
+
+param set-default MPC_YAWRAUTO_MAX 40
+
+param set-default FW_PR_FF 0.5
+param set-default FW_PR_I 0.02
+param set-default FW_PR_IMAX 0.4
+param set-default FW_PR_P 0.08
+param set-default FW_RR_FF 0.6
+param set-default FW_RR_I 0.01
+param set-default FW_RR_IMAX 0.2
+param set-default FW_RR_P 0.05
+param set-default FW_THR_CRUISE 0.75
+
+param set-default VT_ARSP_BLEND 6
+param set-default VT_ARSP_TRANS 12
+param set-default VT_F_TRANS_THR 0.75
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_TYPE 2
+set MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_AAERT
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Generic quad delta VTOL
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output AUX1 Right elevon
+# @output AUX2 Left elevon
+# @output AUX3 Motor
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default MC_ROLL_P 6.5
+param set-default MC_ROLLRATE_P 0.15
+param set-default MC_ROLLRATE_I 0.01
+param set-default MC_ROLLRATE_D 0.003
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_PITCH_P 6.5
+param set-default MC_PITCHRATE_P 0.15
+param set-default MC_PITCHRATE_I 0.01
+param set-default MC_PITCHRATE_D 0.003
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_YAW_P 3.5
+param set-default MC_YAWRATE_P 0.2
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+param set-default MC_YAWRATE_MAX 50
+
+param set-default MPC_XY_P 0.8
+param set-default MPC_XY_VEL_P_ACC 2
+param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_YAWRAUTO_MAX 20
+
+param set-default PWM_AUX_DIS3 950
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_F_TRANS_THR 0.75
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_TYPE 2
+set MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_delta
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Generic AAVVT v-tail plane airframe with Quad VTOL.
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Sander Smeets <sander@droneslab.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.15
+param set-default MC_ROLLRATE_I 0.002
+param set-default MC_ROLLRATE_D 0.003
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.12
+param set-default MC_PITCHRATE_I 0.002
+param set-default MC_PITCHRATE_D 0.003
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_YAW_P 2.8
+param set-default MC_YAWRATE_P 0.22
+param set-default MC_YAWRATE_I 0.02
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+param set-default MC_YAWRATE_MAX 40
+
+param set-default MPC_YAWRAUTO_MAX 40
+
+param set-default PWM_AUX_DIS5 950
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_F_TRANS_THR 0.75
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_TYPE 2
+set MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_AAVVT
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name QuadRanger
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Sander Smeets <sander@droneslab.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default FW_THR_CRUISE 65
+param set-default FW_PR_P 0.08
+param set-default FW_PR_FF 0.5
+param set-default FW_RR_P 0.05
+param set-default FW_RR_FF 0.6
+
+param set-default MIS_YAW_TMT 10
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.15
+param set-default MC_ROLLRATE_I 0.1
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.15
+param set-default MC_PITCHRATE_I 0.1
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_YAW_P 3.5
+param set-default MC_YAWRATE_P 0.6
+param set-default MC_YAWRATE_I 0.04
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+param set-default MC_YAWRATE_MAX 40
+
+param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_Z_VEL_MAX_DN 1.5
+param set-default MPC_TKO_SPEED 1.5
+param set-default MPC_LAND_SPEED 0.8
+param set-default MPC_YAWRAUTO_MAX 40
+
+param set-default PWM_AUX_DIS5 950
+param set-default PWM_AUX_REV1 1
+param set-default PWM_AUX_REV2 1
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_ARSP_TRANS 15
+param set-default VT_ARSP_BLEND 8
+param set-default VT_B_TRANS_DUR 4
+param set-default VT_F_TRANS_THR 0.75
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_TYPE 2
+set MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_AAERT
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Sparkle Tech Ranger VTOL
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Andreas Antener <andreas@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default FW_AIRSPD_MAX   22
+param set-default FW_AIRSPD_MIN   14
+param set-default FW_AIRSPD_TRIM  16
+param set-default FW_L1_PERIOD    25
+param set-default FW_PR_P 0.060
+param set-default FW_P_RMAX_NEG   40
+param set-default FW_P_RMAX_POS   40
+param set-default FW_RR_FF    0.4
+param set-default FW_RR_P 0.04
+param set-default FW_R_RMAX   40
+
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_PITCHRATE_I 0
+param set-default MC_PITCHRATE_MAX 60
+param set-default MC_PITCHRATE_P 0.21
+param set-default MC_PITCH_P 4
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_ROLLRATE_I 0.002
+param set-default MC_ROLLRATE_MAX 60
+param set-default MC_ROLLRATE_P 0.24
+param set-default MC_ROLL_P 4
+param set-default MC_YAWRATE_I 0.02
+param set-default MC_YAWRATE_MAX 40
+param set-default MC_YAWRATE_P 0.18
+
+param set-default MIS_TAKEOFF_ALT 2.5
+param set-default MIS_YAW_TMT 20
+
+param set-default MPC_ACC_HOR_MAX 1
+param set-default MPC_HOLD_MAX_XY 0.5
+param set-default MPC_HOLD_MAX_Z  0.5
+param set-default MPC_LAND_SPEED  1
+param set-default MPC_MANTHR_MIN  0.05
+param set-default MPC_MAN_Y_MAX   120
+param set-default MPC_THR_MIN 0.07
+param set-default MPC_TILTMAX_AIR 35
+param set-default MPC_TILTMAX_LND 20
+param set-default MPC_TKO_SPEED   1
+param set-default MPC_XY_P    0.3
+param set-default MPC_XY_VEL_MAX  3
+param set-default MPC_XY_VEL_P_ACC 1
+param set-default MPC_Z_P 0.5
+param set-default MPC_Z_VEL_P_ACC 2
+param set-default MPC_YAWRAUTO_MAX 40
+
+param set-default NAV_ACC_RAD 3
+
+param set-default PWM_AUX_REV1    1
+param set-default PWM_AUX_REV2    1
+param set-default PWM_AUX_REV3    1
+param set-default PWM_AUX_REV4    1
+
+param set-default PWM_AUX_DIS5 950
+
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_ARSP_TRANS   15
+param set-default VT_B_TRANS_DUR  4
+param set-default VT_F_TRANS_THR    0.6
+param set-default VT_IDLE_PWM_MC 1180
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_TRANS_MIN_TM 5
+param set-default VT_TRANS_TIMEOUT    30
+param set-default VT_TYPE 2
+
+set MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_AAERT
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name CruiseAder Claire
+#
+# @type VTOL Tiltrotor
+# @class VTOL
+#
+# @maintainer Samay Siga <samay_s@icloud.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_AUX_DISARMED 1000
+param set-default PWM_AUX_MAX 2000
+param set-default PWM_AUX_MIN 1000
+param set-default PWM_AUX_RATE 50
+
+param set-default PWM_MAIN_MAX 2000
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 13
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_TILT_FW 0.9
+param set-default VT_TILT_MC 0.08
+param set-default VT_TILT_TRANS 0.5
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_TYPE 1
+set MAV_TYPE 21
+
+set MIXER claire
+set MIXER_AUX claire
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name E-flite Convergence
+#
+# @type VTOL Tiltrotor
+# @class VTOL
+#
+# @maintainer Andreas Antener <andreas@uaventure.com>
+#
+# @output MAIN1 Motor right
+# @output MAIN2 Motor left
+# @output MAIN3 Motor back
+# @output MAIN4 empty
+# @output MAIN5 Tilt servo right
+# @output MAIN6 Tilt servo left
+# @output MAIN7 Elevon right
+# @output MAIN8 Elevon left
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default CBRK_AIRSPD_CHK 162128
+
+param set-default FW_ARSP_MODE 1
+
+param set-default FW_L1_PERIOD 17
+param set-default FW_MAN_R_MAX 50
+param set-default FW_ACRO_X_MAX   270
+param set-default FW_ACRO_Y_MAX   270
+param set-default FW_ACRO_Z_MAX   180
+param set-default FW_PR_FF    0.5
+param set-default FW_PR_P 0.08
+param set-default FW_PSP_OFF  5
+param set-default FW_P_LIM_MAX    30
+param set-default FW_P_LIM_MIN    -30
+param set-default FW_P_RMAX_NEG   60
+param set-default FW_P_RMAX_POS   60
+param set-default FW_RR_FF    0.33
+param set-default FW_RR_P 0.11
+param set-default FW_YR_FF    0.3
+param set-default FW_YR_P 0.05
+
+param set-default MC_PITCHRATE_D  0.003
+param set-default MC_PITCHRATE_P  0.15
+param set-default MC_PITCH_P  6
+param set-default MC_ROLLRATE_D   0.003
+param set-default MC_ROLLRATE_P   0.15
+param set-default MC_ROLL_P   6
+param set-default MC_YAWRATE_MAX  120
+param set-default MC_YAWRATE_P    0.27
+param set-default MC_YAW_P    2.5
+
+param set-default MC_YAWRATE_P 0.3
+param set-default MPC_LAND_SPEED 1.2
+param set-default MPC_TKO_SPEED 2.5
+param set-default MPC_Z_VEL_MAX_UP 3
+
+param set-default PWM_MAIN_RATE 400
+
+param set-default SENS_BOARD_ROT 8
+
+param set-default VT_B_TRANS_DUR  1
+param set-default VT_F_TRANS_DUR  1.2
+param set-default VT_F_TR_OL_TM   4
+param set-default VT_FW_DIFTHR_EN 1
+param set-default VT_FW_DIFTHR_SC 0.17
+param set-default VT_FW_MOT_OFFID 3
+param set-default VT_FW_PERM_STAB 0
+param set-default VT_IDLE_PWM_MC 1200
+param set-default VT_MOT_ID 123
+param set-default VT_TILT_FW  1
+param set-default VT_TILT_MC  0
+param set-default VT_TILT_TRANS   0.45
+param set-default VT_TRANS_MIN_TM 1.2
+param set-default VT_TRANS_P2_DUR 1.3
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_TYPE 1
+set MAV_TYPE 21
+
+set MIXER vtol_convergence
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Vertical Technologies DeltaQuad
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Sander Smeets <sander@droneslab.com>
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 Right elevon
+# @output MAIN6 Left elevon
+# @output MAIN7 Pusher motor
+# @output MAIN8 Pusher reverse channel
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default BAT_CAPACITY 23000
+param set-default BAT_N_CELLS 4
+param set-default BAT_R_INTERNAL 0.0025
+
+param set-default CBRK_AIRSPD_CHK 162128
+param set-default CBRK_IO_SAFETY 22027
+
+param set-default EKF2_GPS_POS_X -0.12
+param set-default EKF2_IMU_POS_X -0.12
+param set-default EKF2_TAU_VEL 0.5
+param set-default EKF2_GPS_P_GATE 10
+param set-default EKF2_GPS_V_GATE 10
+
+param set-default FW_ARSP_MODE 1
+param set-default FW_L1_PERIOD 25
+param set-default FW_PR_FF 0.7
+param set-default FW_PR_I 0.18
+param set-default FW_PR_P 0.15
+param set-default FW_P_TC 0.5
+param set-default FW_PSP_OFF 5
+param set-default FW_R_LIM 35
+param set-default FW_RR_FF 0.9
+param set-default FW_RR_I 0.08
+param set-default FW_RR_P 0.18
+param set-default FW_T_HRATE_FF 0.5
+param set-default FW_T_CLMB_MAX 3
+param set-default FW_T_SINK_MAX 3
+param set-default FW_T_SINK_MIN 1
+param set-default FW_T_VERT_ACC 6
+param set-default FW_THR_CRUISE 0.70
+param set-default FW_THR_SLEW_MAX 1
+param set-default FW_MAN_P_MAX 30
+param set-default FW_P_LIM_MAX 15
+param set-default FW_P_LIM_MIN -25
+param set-default FW_P_RMAX_NEG 45
+param set-default FW_P_RMAX_POS 45
+param set-default FW_R_RMAX 50
+param set-default FW_THR_MIN 0.55
+param set-default FW_BAT_SCALE_EN 1
+param set-default FW_THR_ALT_SCL 2.7
+param set-default FW_T_RLL2THR 20
+
+param set-default LNDMC_ALT_MAX 9999
+param set-default LNDMC_XY_VEL_MAX 1
+param set-default LNDMC_Z_VEL_MAX 0.7
+
+param set-default MC_ROLL_P 6.5
+param set-default MC_ROLLRATE_P 0.16
+param set-default MC_ROLLRATE_I 0.01
+param set-default MC_ROLLRATE_D 0.003
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_ROLLRATE_MAX 80
+param set-default MC_PITCH_P 6.5
+param set-default MC_PITCHRATE_P 0.15
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_PITCHRATE_D 0.003
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_PITCHRATE_MAX 80
+param set-default MC_YAW_P 3.5
+param set-default MC_YAWRATE_P 0.2
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+param set-default MC_YAWRATE_MAX 20
+param set-default MC_AIRMODE 1
+
+param set-default MIS_DIST_1WP 100
+param set-default MIS_DIST_WPS 100000
+param set-default MIS_TAKEOFF_ALT 15
+
+param set-default MPC_XY_P 0.8
+param set-default MPC_XY_VEL_P_ACC 2
+param set-default MPC_XY_VEL_MAX 5
+param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_LAND_SPEED 1.2
+param set-default MPC_TILTMAX_LND 35
+param set-default MPC_Z_VEL_MAX_UP 1.5
+param set-default MPC_Z_VEL_MAX_DN 1.5
+param set-default MPC_HOLD_MAX_XY 0.5
+param set-default MPC_HOLD_MAX_Z 0.5
+param set-default MPC_TKO_RAMP_T 0.8
+param set-default MPC_XY_CRUISE 5
+param set-default MPC_TILTMAX_AIR 25
+param set-default MPC_TILTMAX_LND 25
+param set-default MPC_YAWRAUTO_MAX 20
+
+param set-default NAV_DLL_ACT 0
+param set-default NAV_LOITER_RAD 100
+
+param set-default PWM_AUX_DISARMED 950
+
+param set-default PWM_MAIN_DIS5 1500
+param set-default PWM_MAIN_DIS6 1500
+param set-default PWM_MAIN_DIS7 900
+param set-default PWM_MAIN_DIS8 900
+
+param set-default PWM_MAIN_RATE 400
+
+param set-default SENS_BOARD_ROT 18
+
+# TELEM2 config
+param set-default MAV_1_CONFIG 102
+param set-default MAV_1_RATE 5000
+param set-default MAV_1_FORWARD 1
+param set-default SER_TEL2_BAUD 57600
+
+param set-default VT_TYPE 2
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+param set-default VT_F_TRANS_THR 1
+param set-default VT_DWN_PITCH_MAX 8
+param set-default VT_FW_QC_P 55
+param set-default VT_FW_QC_R 55
+param set-default VT_TRANS_MIN_TM 15
+param set-default VT_B_TRANS_DUR 8
+param set-default VT_WV_LND_EN 1
+param set-default VT_WV_LTR_EN 1
+param set-default VT_FWD_THRUST_SC 4
+param set-default VT_F_TRANS_DUR 1
+param set-default VT_IDLE_PWM_MC 1025
+param set-default VT_B_REV_OUT 0.5
+param set-default VT_B_TRANS_THR 0.7
+param set-default VT_FW_PERM_STAB 1
+param set-default VT_TRANS_TIMEOUT 22
+param set-default VT_F_TRANS_RAMP 4
+
+param set-default COM_RC_OVERRIDE 0
+set MAV_TYPE 22
+
+set MIXER deltaquad
+set MIXER_AUX pass
+
+set PWM_OUT 1234
+set PWM_AUX_OUT 12345

+#!/bin/sh
+#
+# @name BabyShark VTOL
+#
+# @type Standard VTOL
+# @class VTOL
+#
+# @maintainer Silvan Fuhrer <silvan@auterion.com>
+#
+# @output MAIN1 Ailerons
+# @output MAIN2 A-tail left
+# @output MAIN3 Pusher motor
+# @output MAIN4 A-tail right
+# @output MAIN5 motor 1
+# @output MAIN6 motor 2
+# @output MAIN7 motor 3
+# @output MAIN8 motor 4
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+
+param set-default BAT_N_CELLS 6
+
+param set-default FW_AIRSPD_MAX 30
+param set-default FW_AIRSPD_MIN 19
+param set-default FW_AIRSPD_TRIM 23
+param set-default FW_L1_R_SLEW_MAX 40
+param set-default FW_LND_EARLYCFG 1
+param set-default FW_MAN_P_MAX 30
+param set-default FW_PR_I 0.1
+param set-default FW_PSP_OFF 3
+param set-default FW_P_LIM_MAX 18
+param set-default FW_P_LIM_MIN -25
+param set-default FW_RLL_TO_YAW_FF 0.1
+param set-default FW_RR_I 0.1
+param set-default FW_RR_P 0.08
+param set-default FW_R_LIM 45
+param set-default FW_R_RMAX 50
+param set-default FW_THR_CRUISE 0.65
+param set-default FW_THR_MIN 0.3
+param set-default FW_THR_SLEW_MAX 0.6
+param set-default FW_T_HRATE_FF 0
+param set-default FW_T_SINK_MAX 15
+param set-default FW_T_SINK_MIN 3
+param set-default FW_YR_I 0.1
+param set-default FW_YR_P 0.15
+
+param set-default IMU_GYRO_CUTOFF 40
+
+param set-default IMU_DGYRO_CUTOFF 15
+param set-default MC_PITCHRATE_I 0.2
+param set-default MC_PITCHRATE_MAX 60
+param set-default MC_ROLLRATE_I 0.2
+param set-default MC_ROLLRATE_MAX 60
+param set-default MC_YAWRATE_I 0.15
+param set-default MC_YAWRATE_MAX 40
+param set-default MC_YAWRATE_P 0.3
+
+param set-default MIS_TAKEOFF_ALT 30
+
+param set-default MPC_ACC_DOWN_MAX 2
+param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_ACC_UP_MAX 3
+param set-default MC_AIRMODE 1
+param set-default MPC_JERK_AUTO 4
+param set-default MPC_LAND_SPEED 1
+param set-default MPC_MAN_TILT_MAX 25
+param set-default MPC_MAN_Y_MAX 40
+param set-default MPC_POS_MODE 3
+param set-default MPC_SPOOLUP_TIME 1.5
+param set-default MPC_THR_HOVER 0.45
+param set-default MPC_TILTMAX_AIR 25
+param set-default MPC_TKO_RAMP_T 1.8
+param set-default MPC_TKO_SPEED 1
+param set-default MPC_VEL_MANUAL 3
+param set-default MPC_XY_CRUISE 3
+param set-default MPC_XY_VEL_MAX 3.5
+param set-default MPC_YAWRAUTO_MAX 40
+param set-default MPC_Z_VEL_MAX_DN 1.5
+param set-default MPC_Z_VEL_MAX_UP 2
+
+param set-default NAV_ACC_RAD 3
+
+param set-default PWM_MAIN_DIS3 1000
+param set-default PWM_MAIN_MIN3 1120
+param set-default PWM_MAIN_MIN 950
+
+param set-default SENS_BOARD_ROT 4
+
+param set-default VT_ARSP_BLEND 10
+param set-default VT_ARSP_TRANS 21
+param set-default VT_B_DEC_MSS 1.5
+param set-default VT_B_TRANS_DUR 12
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_FWD_THRUST_SC 1.2
+param set-default VT_FW_MOT_OFFID 5678
+param set-default VT_F_TR_OL_TM 8
+param set-default VT_IDLE_PWM_MC 1000
+param set-default VT_MOT_ID 5678
+param set-default VT_PSHER_RMP_DT 2
+param set-default VT_TRANS_MIN_TM 4
+param set-default VT_TYPE 2
+
+set MAV_TYPE 22
+
+set MIXER babyshark
+set MIXER_AUX pass
+
+set PWM_OUT 5678
+set PWM_AUX_OUT 1234

+#!/bin/sh
+#
+# @name Generic Quadplane VTOL Tiltrotor
+#
+# @type VTOL Tiltrotor
+# @class VTOL
+#
+# @maintainer
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output AUX1 Motor tilt front left
+# @output AUX2 Motor tilt front right
+# @output AUX3 Motor tilt rear left
+# @output AUX4 Motor tilt rear right
+# @output AUX5 Aileron left
+# @output AUX6 Aileron right
+# @output AUX7 Elevator
+# @output AUX8 Rudder
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_IDLE_PWM_MC 1100
+param set-default VT_TYPE 1
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 24
+set MAV_TYPE 21
+
+set MIXER quad_x
+set MIXER_AUX vtol_TTTTAAER
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Generic Octoplane VTOL
+#
+# @type VTOL Octoplane
+# @class VTOL
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 motor 5
+# @output MAIN6 motor 6
+# @output MAIN7 motor 7
+# @output MAIN8 motor 8
+# @output AUX1 Aileron 1
+# @output AUX2 Aileron 2
+# @output AUX3 Elevator
+# @output AUX4 Rudder
+# @output AUX5 Throttle
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default PWM_AUX_DIS5 950
+param set-default PWM_MAIN_RATE 400
+
+param set-default VT_TYPE 2
+param set-default VT_MOT_ID 12345678
+param set-default VT_FW_MOT_OFFID 12345678
+set MAV_TYPE 22
+
+set MIXER octo_cox
+set MIXER_AUX vtol_AAERT
+
+set PWM_OUT 12345678

+#!/bin/sh
+#
+# @name Generic Tailsitter
+#
+# @type VTOL Duo Tailsitter
+# @class VTOL
+#
+# @output MAIN1 motor right
+# @output MAIN2 motor left
+# @output MAIN5 elevon right
+# @output MAIN6 elevon left
+#
+# @maintainer Roman Bapst <roman@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_MOT_COUNT 2
+param set-default VT_TYPE 0
+
+param set-default MAV_TYPE 19
+set MAV_TYPE 19
+set MIXER vtol_tailsitter_duo
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Generic Tricopter Y+ Geometry
+#
+# @type Tricopter Y+
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 yaw servo
+#
+# @maintainer Trent Lukaczyk <aerialhedgehog@gmail.com>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER tri_y_yaw+
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Generic Tricopter Y- Geometry
+#
+# @type Tricopter Y-
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 yaw servo
+#
+# @maintainer Trent Lukaczyk <aerialhedgehog@gmail.com>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+set MIXER tri_y_yaw-
+
+set PWM_OUT 1234

+#!/bin/sh
+#
+# @name Esky (Big) Lama v4
+#
+# @type Coaxial Helicopter
+# @class Copter
+#
+# @output MAIN1 Left swashplate servomotor, pitch axis
+# @output MAIN2 Right swashplate servomotor, roll axis
+# @output MAIN3 Upper rotor (CCW)
+# @output MAIN4 Lower rotor (CW)
+#
+# @maintainer Emmanuel Roussel
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+set MIXER coax
+
+
+param set-default MC_ROLL_P 6.5
+param set-default MC_ROLLRATE_P 0.17
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_ROLLRATE_D 0.005
+param set-default MC_ROLLRATE_FF 0
+param set-default MC_PITCH_P 6.5
+param set-default MC_PITCHRATE_P 0.17
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_PITCHRATE_D 0.005
+param set-default MC_PITCHRATE_FF 0
+param set-default MC_YAW_P 2
+param set-default MC_YAWRATE_P 0.1
+param set-default MC_YAWRATE_I 0.1
+param set-default MC_YAWRATE_D 0
+param set-default MC_YAWRATE_FF 0
+
+param set-default NAV_ACC_RAD 2
+
+param set-default PWM_AUX_RATE 50
+param set-default PWM_MAIN_DISARM 900
+param set-default PWM_MAIN_MIN 1075
+param set-default PWM_MAIN_MAX 1950
+param set-default PWM_MAIN_RATE 400
+
+param set-default RTL_RETURN_ALT 30
+param set-default RTL_DESCEND_ALT 10
+# This is the gimbal pass mixer
+set MIXER_AUX pass
+
+# use PWM parameters for throttle channel
+set PWM_AUX_OUT 1234
+set PWM_OUT 34

+#!/bin/sh
+#
+# @name Blade 130X
+#
+# @type Helicopter
+# @class Copter
+#
+# @maintainer Bart Slinger <bartslinger@gmail.com>
+#
+# @output MAIN1 main motor
+# @output MAIN2 front swashplate servo
+# @output MAIN3 right swashplate servo
+# @output MAIN4 left swashplate servo
+# @output MAIN5 tail-rotor servo
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+# Configure as helicopter (number 4 defined in commander_helper.cpp)
+set MAV_TYPE 4
+
+set MIXER blade130
+
+#set PWM_OUT 1234
+
+
+param set-default ATT_BIAS_MAX 0
+
+param set-default CBRK_IO_SAFETY 22027
+
+param set-default MC_ROLL_P 5
+param set-default MC_ROLLRATE_P 0
+param set-default MC_ROLLRATE_I 0
+param set-default MC_ROLLRATE_D 0
+param set-default MC_ROLLRATE_FF 0.15
+param set-default MC_PITCH_P 6.5
+param set-default MC_PITCHRATE_P 0
+param set-default MC_PITCHRATE_I 0
+param set-default MC_PITCHRATE_D 0
+param set-default MC_PITCHRATE_FF 0.15
+param set-default MC_YAW_P 3
+param set-default MC_YAWRATE_P 0.1
+param set-default MC_YAWRATE_I 0
+param set-default MC_YAWRATE_D 0
+param set-default MC_ROLLRATE_MAX 720
+param set-default MC_PITCHRATE_MAX 720
+param set-default MC_YAWRATE_MAX 400
+param set-default MC_ACRO_R_MAX 360
+param set-default MC_ACRO_P_MAX 360
+
+param set-default MPC_THR_MIN 0.06
+param set-default MPC_MANTHR_MIN 0.06
+
+param set-default PWM_MAIN_MIN 1075

+#!/bin/sh
+#
+# @name ThunderFly Auto-G2
+#
+# @type Autogyro
+# @class Autogyro
+#
+# @output MAIN1 rotor_head_L
+# @output MAIN2 rotor_head_R
+# @output MAIN3 elevator
+# @output MAIN4 rudder
+# @output MAIN5 rudder (second, optional)
+# @output MAIN6 throttle
+# @output MAIN7 wheel
+#
+# @output AUX1 feed-through of RC AUX1 channel for prerotator (optional)
+# @output AUX2 feed-through of RC AUX2 channel for release device (optional)
+#
+# @url https://github.com/ThunderFly-aerospace/Auto-G2/
+# @maintainer ThunderFly s.r.o., Roman Dvorak <dvorakroman@thunderfly.cz>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+
+param set-default BAT_CAPACITY 2500
+param set-default BAT_N_CELLS 3
+
+param set-default PWM_AUX_RATE 50
+param set-default PWM_MAIN_RATE 50
+
+param set-default SENS_BOARD_ROT 8
+
+param set-default FW_AIRSPD_MAX 20
+param set-default FW_AIRSPD_MIN 7
+param set-default FW_AIRSPD_TRIM 13
+param set-default FW_THR_CRUISE 0.8
+
+param set-default FW_MAN_P_MAX 25
+param set-default FW_MAN_R_MAX 25
+param set-default FW_PR_I 0.02
+param set-default FW_R_LIM 40
+param set-default FW_P_LIM_MAX 25
+param set-default FW_P_LIM_MIN -5
+param set-default FW_P_RMAX_NEG 20
+set MIXER TF-AutoG2
+set MIXER_AUX pass

+#!/bin/sh
+#
+# @name ThunderFly TF-G2
+#
+# @type Autogyro
+# @class Autogyro
+#
+# @output MAIN2 rotor_head_L
+# @output MAIN3 rotor_head_R
+# @output MAIN4 rudder
+# @output MAIN5 throttle
+#
+#
+# @url https://github.com/ThunderFly-aerospace/TF-G2/
+# @maintainer ThunderFly s.r.o., Roman Dvorak <dvorakroman@thunderfly.cz>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+
+param set-default BAT_CAPACITY 3300
+param set-default BAT_N_CELLS 3
+
+param set-default PWM_AUX_RATE 50
+param set-default PWM_MAIN_RATE 50
+
+param set-default SENS_BOARD_ROT 4
+
+param set-default FW_AIRSPD_MAX 20
+param set-default FW_AIRSPD_MIN 7
+param set-default FW_AIRSPD_TRIM 13
+param set-default FW_THR_CRUISE 0.8
+
+param set-default FW_MAN_P_MAX 25
+param set-default FW_MAN_R_MAX 25
+param set-default FW_PR_I 0.02
+param set-default FW_R_LIM 40
+param set-default FW_P_LIM_MAX 25
+param set-default FW_P_LIM_MIN -5
+param set-default FW_P_RMAX_NEG 20
+set MIXER TF-G2
+set MIXER_AUX pass

+#!/bin/sh
+#
+# @name ThunderFly balloon TF-B1
+#
+# @type Balloon
+# @class Balloon
+#
+#
+# @url https://github.com/ThunderFly-aerospace/TF-B1/
+# @maintainer ThunderFly s.r.o.
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.balloon_defaults
+
+
+param set-default COM_PREARM_MODE 2  # always in prearm state
+param set-default CBRK_IO_SAFETY 22027
+param set-default SDLOG_PROFILE 17
+param set-default SDLOG_MODE 2
+param set-default MAV_0_MODE 1
+param set-default MAV_0_CONFIG 102
+param set-default GPS_UBX_DYNMODEL 8
+param set-default SER_TEL2_BAUD 9600
+
+param set-default SENS_BOARD_ROT 0
+        param set MAV_TYPE 8  # MAV_TYPE_FREE_BALLOON
+
+
+set MIXER IO_pass
+set MIXER_AUX pass

+#!/bin/sh
+#
+# @name Standard Plane
+#
+# @type Standard Plane
+# @class Plane
+#
+# @output MAIN1 aileron
+# @output MAIN2 elevator
+# @output MAIN3 throttle
+# @output MAIN4 rudder
+# @output MAIN5 flaps
+# @output MAIN6 gear
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+param set-default PWM_AUX_RATE 50
+param set-default PWM_MAIN_RATE 50
+
+set MIXER AETRFG
+
+# Rate must be set by group (see pwm info).
+# Throttle is in the same group as servos.

+#!/bin/sh
+#
+# @name Bormatec Maja
+#
+# @type Standard Plane
+# @class Plane
+#
+# @output MAIN1 aileron
+# @output MAIN2 aileron
+# @output MAIN3 elevator
+# @output MAIN4 rudder
+# @output MAIN5 throttle
+# @output MAIN6 wheel
+# @output MAIN7 flaps
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Andreas Antener <andreas@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+param set-default FW_AIRSPD_MIN 10
+param set-default FW_AIRSPD_TRIM 15
+param set-default FW_AIRSPD_MAX 20
+
+param set-default FW_MAN_P_MAX 55
+param set-default FW_MAN_R_MAX 55
+param set-default FW_R_LIM 55
+
+param set-default FW_WR_FF 0.2
+param set-default FW_WR_I 0.2
+param set-default FW_WR_IMAX 0.8
+param set-default FW_WR_P 1
+param set-default FW_W_RMAX 0
+
+# set disarmed value for the ESC
+param set-default PWM_MAIN_DISARM 1000
+
+
+set MIXER AAERTWF
+
+# use PWM parameters for throttle channel
+set PWM_OUT 5

+#!/bin/sh
+#
+# @name Applied Aeronautics Albatross
+#
+# @type Plane A-Tail
+# @class Plane
+#
+# @output MAIN1 aileron right
+# @output MAIN2 aileron left
+# @output MAIN3 v-tail right
+# @output MAIN4 v-tail left
+# @output MAIN5 throttle
+# @output MAIN6 wheel
+# @output MAIN7 flaps right
+# @output MAIN8 flaps left
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Andreas Antener <andreas@uaventure.com>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+param set-default FW_AIRSPD_MIN 10
+param set-default FW_AIRSPD_TRIM 15
+param set-default FW_AIRSPD_MAX 20
+
+param set-default FW_MAN_P_MAX 55
+param set-default FW_MAN_R_MAX 55
+param set-default FW_R_LIM 55
+
+param set-default FW_WR_FF 0.2
+param set-default FW_WR_I 0.2
+param set-default FW_WR_IMAX 0.8
+param set-default FW_WR_P 1
+param set-default FW_W_RMAX 0
+
+# set disarmed value for the ESC
+param set-default PWM_MAIN_DISARM 1000
+
+
+set MIXER AAVVTWFF
+
+# use PWM parameters for throttle channel
+set PWM_OUT 5

+#!/bin/sh
+#
+# @name X-UAV Mini Talon
+#
+# @type Plane V-Tail
+# @class Plane
+#
+# @output MAIN1 aileron right
+# @output MAIN2 aileron left
+# @output MAIN3 v-tail right
+# @output MAIN4 v-tail left
+# @output MAIN5 throttle
+# @output MAIN6 wheel
+# @output MAIN7 flaps right
+# @output MAIN8 flaps left
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Friedrich Beckmann <friedrich.beckmann@hs-augsburg.de>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+param set-default FW_AIRSPD_MIN 10
+param set-default FW_AIRSPD_TRIM 15
+param set-default FW_AIRSPD_MAX 20
+
+param set-default FW_MAN_P_MAX 55
+param set-default FW_MAN_R_MAX 55
+param set-default FW_R_LIM 55
+
+param set-default FW_WR_FF 0.2
+param set-default FW_WR_I 0.2
+param set-default FW_WR_IMAX 0.8
+param set-default FW_WR_P 1
+param set-default FW_W_RMAX 0
+
+# set disarmed value for the ESC
+param set-default PWM_MAIN_DISARM 1000
+
+# The Mini Talon does not have a wheel and
+# no flaps. I leave them here because the mixer
+# computes also wheel and flap controls.
+set MIXER AAVVTWFF_vtail
+
+# use PWM parameters for throttle channel
+set PWM_OUT 5

+#!/bin/sh
+#
+# @name Generic Dodecarotor cox geometry
+#
+# @type Dodecarotor cox
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 motor 5
+# @output MAIN6 motor 6
+#
+# @output AUX1 motor 7
+# @output AUX2 motor 8
+# @output AUX3 motor 9
+# @output AUX4 motor 10
+# @output AUX5 motor 11
+# @output AUX6 motor 12
+#
+# @maintainer Ian McNanie <ianmcnanie@gmail.com>
+# @maintainer William Peale <develop707@gmail.com>
+#
+# @board bitcraze_crazyflie exclude
+#
+
+set VEHICLE_TYPE mc
+
+
+param set-default NAV_ACC_RAD 2
+
+param set-default PWM_AUX_RATE 400
+param set-default PWM_AUX_DISARMED 900
+param set-default PWM_AUX_MIN 1075
+param set-default PWM_AUX_MAX 1950
+
+param set-default PWM_MAIN_MIN 1075
+param set-default PWM_MAIN_MAX 1950
+param set-default PWM_MAIN_RATE 400
+
+param set-default RTL_DESCEND_ALT 10
+param set-default RTL_RETURN_ALT 30
+set MIXER dodeca_top_cox
+set MIXER_AUX dodeca_bottom_cox
+
+# Need to set all 8 channels
+set PWM_OUT 12345678
+set PWM_AUX_OUT 123456